IC694ALG223

IC694ALG223 16-Channel Analog Current Input Module

The IC694ALG223 provides 16 single-ended input channels. Each input can be configured using the configuration software for any of the following input ranges:

   4 to 20 mA
   0 to 20 mA
   4 to 20 mA Enhanced

High and low alarm limits are available on all ranges. In the 4 to 20 mA Enhanced range, a low alarm limit can be set to detect input current from 4 mA to 0 mA, providing open-wire fault detection for 4-20 mA applications.

The module also reports module status and external power supply status to the CPU using the assigned program reference addresses.

This module can be installed in any I/O slot in an RX3i system.

Module Power

This module consumes 120 mA from the 5 VDC bus on the PLC backplane. It also requires 65 mA plus loop current(s) from a user-supplied +24 VDC source.

LED Indicators

MODULE OK LED provides the following status information upon power-up:

   ON: Status is OK, module is configured
   OFF: No backplane power or software is not running (watchdog timer timed out)
   Continuous rapid flashing: Configuration data not received from CPU
   Slow flashing, then OFF: Power-up diagnostics failed or encountered a code execution error

User Supply LED indicates that the external 24 VDC power supply is within specifications.

Specifications: ALG223

   Number of Channels: 1 to 16 selectable, single-ended
   Input Current Ranges: 0 to 20 mA, 4 to 20 mA, and 4 to 20 mA Enhanced (selectable per channel)
   Calibration: Factory calibrated:
        4 μA per count in the 4 to 20 mA range
        5 μA per count in the 0 to 20 mA and 4 to 20 mA Enhanced ranges
   Update Rate: 13 milliseconds (all 16 channels)
   Resolution:
        4 to 20 mA range: 4 μA/bit
        0 to 20 mA range: 5 μA/bit
        4 to 20 mA Enhanced range: 5 μA/bit
   Accuracy: +/-0.25% of full scale @ 25°C; +/-0.5% over the specified operating temperature range
   Linearity: < 1 LSB in the 4 to 20 mA range
   Isolation (Field to Backplane): 250 VAC continuous; 1500 VAC for 1 minute
   Common Mode Voltage: 0 volts (single-ended channels)
   Cross-Channel Rejection: > 80 dB from DC to 1 kHz
   Input Impedance: 250 Ohms
   Low Pass Filter Response: 19 Hz
   External Supply Voltage Range: 20 to 30 VDC
   Power Consumption:
        120 mA from the +5 VDC backplane bus
        65 mA from the +24 VDC external power supply (in addition to loop current)

Configuration: ALG223

IC694ALG223 is configured using configuration software. The configurable parameters are as follows:

   Active Channels: 1 to 16 – the number of channels to be scanned in sequential order
   Reference Address for Input Data: The memory location where input data from the module is stored. Each channel provides 16 bits of analog input data to the PLC CPU.
   Reference Address for Status Data: The memory location where status information starts.
   Range: 4-20 mA (default), 0-20 mA, or 4-20 mA Enhanced
        In the 4-20 mA range, input currents are reported as values from 0 to 32000 units to the CPU.
        In the 0-20 mA range, input currents from 0 to 20 mA are reported as values from 0 to 32000 units.
        In the 4-20 mA Enhanced range, currents below 4 mA are reported as negative values, with 0 represented as -8000 units.
   Alarm Limits: You can assign low and high alarm limits for each channel.

Data Format: ALG223

The module’s 12-bit resolution analog input data is stored in the PLC CPU in 16-bit 2’s complement format.

   In the 4 to 20 mA range, 4 mA corresponds to a count of 0 and 20 mA corresponds to a count of 32000.
   In the 0 to 20 mA range, 0 mA corresponds to a count of 0 and 20 mA corresponds to a count of 32000.
   In the 4 to 20 mA Enhanced range, 0 mA corresponds to a count of -8000, 4 mA to 0, and 20 mA to 32000.

Status Data: ALG223

The module can be configured to return 8, 16, 24, 32, or 40 status bits to the CPU. These status bits provide information such as:

   Module OK
   Power Supply OK
   High and Low Alarm status for each channel

>> IC694ALG223 Analog modules User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC694ALG223 Analog modules and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."