IC693BEM330

IC693BEM330 FIP Remote I/O Scanner Module

The FIP (Factory Instrumentation Protocol) Remote I/O Scanner (catalog number IC693BEM330) is an intelligent module that interfaces Series 90-30 I/O modules to a FIP bus. Up to 19 I/O modules can be accommodated by using two 10-slot baseplates connected by an expansion cable. Together, the Remote I/O Scanner and the modules it serves are referred to as an I/O Nest. The FIP Nest can include most Series 90-30 I/O modules.

The host CPU can be any type of CPU capable of communicating on a FIP bus. A module in the host (such as a FIP Bus Controller) provides the necessary interface between the FIP bus and the host CPU.

Features of the Remote I/O Scanner
The FIP Remote I/O Scanner performs the following basic functions:

  • Controls operation of the I/O nest in the selected mode
  • Scans discrete and analog I/O modules and maintains I/O scan timing
  • Maps I/O data to FIP application variables
  • Detects module and system faults and reports them to the FIP network
  • Permits standalone configuration using Hand-Held Programmer
  • Retains its network configuration through loss of power
  • Permits I/O forcing from the Hand-Held Programmer
  • Detects and records input transitions
  • Supports FIP messaging services
  • Responds to an external synchronization signal
  • Provides blinking or pulsed outputs
  • Provides input filtering and chatter detection

FIP Bus Interface
The Remote I/O Scanner communicates at a data rate of 1MHz. There are two versions of the FIP communications standard: FIP and WORLD FIP. A DIP switch on the module is used to select the version that will be used by the Remote I/O Scanner. (The same communications method will then be used on both bus cables).

The DIP switch on the module must be set to the FIP position for the Remote I/O Scanner to communicate with a Series 90-70 PLC.

Module Description
The FIP Remote I/O Scanner is a standard Series 90–30 PLC module that plugs easily into the backplane of the baseplate.

Connectors
The front of the module has the following connectors:
  • 9-pin male D connectors for two FIP bus cables. A bus can be disconnected from the module without disturbing the continuity of the bus. The second bus is a backup for the first bus; its use is optional.
  • Connector for a FIP synchronization cable. It requires a mating connector such as Molex #39-01-4031. The synchronization capability is not used in a Series 90-70 PLC application.
  • The lug below the Synchro connector is used for the module ground wire (provided). The other end of the ground wire must be connected to the mounting bolt on the lower left corner of the baseplate and to chassis ground.

LEDs
There are two pairs of LEDs at the top of the module. The upper pair is for channel 1 and the lower pair is for channel 2.

The green Carrier Detected LEDs indicate the presence of a carrier-detect signal on their respective channels.

The red Transmission Enabled LEDs indicate the module is generating transmissions on their respective channels.



+  IC693BEM330 User manual (pdf)

>> Ge fanuc 90-30 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: IC693BEM330 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."