Ge VAT300 fault codes


Hi everyone,

    Overcurrent Trip (OC)
- Description: The inverter stops and output is cut off if the output current exceeds the preset value.
- Cause: Possible overload or short circuit.
+ Solution: Check for and reduce overload, or locate and repair the short circuit.

    Overvoltage Trip (OV)
- Description: The inverter stops and output is cut off if the DC voltage in the main circuit exceeds the preset value.
- Cause: Sudden reduction in load or regenerative power causing voltage spike.
+ Solution: Check the load and adjust settings to prevent overvoltage.

    Undervoltage Trip (UV)

- Description: The inverter stops and output is cut off if the DC voltage drops to approximately 65% or less due to a power failure or voltage drop.
- Cause: Power failure or significant voltage drop.
+ Solution: Check the power supply and ensure it is stable.

    Overcurrent Limit
- Description: Output frequency is automatically adjusted to keep output current below the overcurrent limit set with B18-0 in case of overload.
- Cause: Overload condition.
+ Solution: Adjust the overcurrent limit setting or reduce the load.

    Overvoltage Limit
- Description: Output frequency is automatically adjusted to prevent the DC voltage in the main circuit from exceeding the preset value.
- Cause: Regenerative power causing an increase in DC voltage.
+ Solution: Adjust settings to manage regenerative power and prevent overvoltage.

    Overload Trip (OL)
- Description: The inverter stops and output is cut off if the overload characteristics set with C22-0, 1, 2, and 3 are exceeded.
- Cause: Motor overload.
+ Solution: Adjust overload settings or reduce load on the motor.

    Overheat (UOH)
- Description: The inverter stops and output is cut off when the heat sink temperature exceeds the preset value.
- Cause: Inadequate cooling or excessive ambient temperature.
+ Solution: Improve cooling, clean vents, or reduce ambient temperature.

    Self-diagnosis (IO, dER, CPU)
- Description: Built-in CPU, peripheral circuits, and data are tested and monitored for abnormalities.
- Cause: Potential hardware or software issues.
+ Solution: Check for error codes and refer to the manual for specific troubleshooting steps.

    Grounding Trip (GRD)
- Description: The inverter stops and output is cut off if a ground fault is detected.
- Cause: Ground fault in the power cable or motor.
+ Solution: Check and restore the grounding point.

    Power Module Fault (PM)
- Description: Inverter stops if a fault is detected in the operation of the main circuit power module protection function.
- Cause: Possible failure of the power module.
+ Solution: Check the power module and replace if necessary.

    Phase Failure (PHL)
- Description: The inverter stops and output is shut off if a phase failure is detected in the main circuit input/output.
- Cause: Phase failure in power supply.
+ Solution: Check the power supply and wiring for phase continuity.

    Emergency Stop (EMS)
- Description: The sequence input EMS has been activated, causing the inverter to stop.
- Cause: Activation of the emergency stop signal.
+ Solution: Check the signal wiring and ensure that the emergency stop is not engaged.

    Power Module (PM-n)
- Description: Indicates activation of the short circuit protection circuit in the power module.
- Cause: Possible short circuit in the load or power module failure.
+ Solution: Check and replace the power module if necessary. Restore the grounded point and improve the installation environment regarding noise.


+ Ge VAT300 User manuals >

+ Ge VAT300 Fault Codes 1 >

+ Ge VAT300 Fault Codes 2 >

+ Ge VAT300 Fault Codes 3 >


+ General Electric 2. Main page >

+ VFD Homepage > 


-

"* The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."  03.01.2013