Ge VAT2000 fault codes 3
Hi everyone,
General Electric VAT2000 VFD Troubleshooting without a Fault Display
When there's no fault display, here's how to figure out what might be wrong and what to do:
Motor Doesn't Start
- Check the Wiring: Make sure the input/output wiring is correct. There might be a problem with the power supply or a phase might be missing.
- Check the Load: The motor might be stuck, or the load might be too heavy. Try lightening the load.
- Check Settings: Make sure the reverse run interlock function (C09-3) and other settings are correct.
- Check the Voltage: Make sure the VAT2000 is sending out the right voltage to the motor.
- Check Local/Remote Setting: Make sure it's set to the right mode for your setup.
- Check the Encoder Signal: Make sure it's being received correctly.
Motor Runs in the Opposite Direction
- Check the Phase Sequence: Make sure the U, V, and W output terminals are connected in the right order.
- Check the Wiring for Forward/Reverse Run: Make sure the wires are connected to the right terminals. For forward run, connect RUN to RY0. For reverse run, connect PSI1 to RY0 (when the input terminal function setting is C03-0=1, which is the default value).
Motor Runs but Speed Doesn't Change
- Check the Load: It might be too heavy. Try reducing it.
- Check the Frequency Setting: The signal level might be too low. Make sure the circuit and signal level are correct.
Motor Acceleration/Deceleration Isn't Smooth
- Adjust the Time Settings: The acceleration/deceleration time setting (A01-0, 1) might be too low. Try increasing it.
Motor Speed Varies During Constant Speed Operation
- Check the Load: It might be changing too much or be too heavy. Try reducing the load or its fluctuation.
- Check the Inverter-Motor Ratings: Make sure they match the load. If not, select a set that does.
Motor Speed Is Too High or Low
- Check the Motor Specifications: The number of poles or voltage might be wrong.
- Check the Frequency Settings: The maximum frequency (speed) or base frequency might be set incorrectly.
- Check the Terminal Voltage: It might be too low. Try using a thicker output cable.
Overvoltage Limit
- If the output frequency suddenly drops, the DC voltage might rise due to regenerative power. The output frequency automatically adjusts to keep the DC voltage from going above the preset value.
Undervoltage (UV-1~UV-9)
- A drop in voltage, phase dropout, or power supply failure might have occurred. Check and correct the power supply system if necessary.
Overheat (UOH)
- There might be a problem with the cooling fan, the ambient temperature might have risen, the fan or heatsink might be clogged, or the carrier frequency might be set too high. Take appropriate actions like replacing the fan, lowering the temperature, cleaning the fan or heatsink, or checking the carrier frequency settings.
Automatic Tuning Abnormal Completion (ATT-n)
- The motor might not be connected correctly, the B00 and B01 parameters might be set incorrectly, the load and machine might not be separated, or the motor might vibrate. Check connections, parameter settings, separate the load and machine if necessary, increase acceleration/deceleration times, and adjust the torque stabilizing gain (B18-2) if needed.
Overload (OL-1)
- The motor might be overloaded. Reduce the load or increase the motor and inverter capacity. If this occurs at low speed, try lowering the boost (A02-2) or brake voltage (A03-0).
Grounding (GRD.1~GRD.9)
- A ground fault might have occurred in the output line or motor. Restore the grounded point.
I/O Errors (IO-1 to IO-F)
- Various I/O errors can occur, such as gate turn-off circuit error, A/D converter error, current detection error, retry time-out, thermistor error, and speed detection error. Each error requires specific checks and actions, such as looking for noise sources, checking connections, resetting the VAT2000, and ensuring proper connection of the thermistor and speed detector.
CPU Errors (CPU-1 to CPU-8)
- The unit might be malfunctioning due to external noise, the control circuit might be faulty, and for all sub-codes other than 8, turning the power off and on once might help.
EEPROM Data Error
- The parameter setting value might be incorrect. To correct it, select D20-2 in monitor mode, press the set key to display the erroneous parameter, set the correct parameter, and display the parameters in order with the knob.
+ Ge VAT2000 VFD User manual >>
+ General Electric 2. Main page >
+ VFD Homepage >