IC693CBL315

The IC693CBL315 was a 10 feet (3 meter) long I/O interface cable designed for use with high-density (32-point) I/O modules in the Series 90-30 PLC system. It connected to one of the 24-pin connectors on the module, with stripped, tinned, and labeled leads on the other end. However, this cable has been obsolete since late 1998 and has been replaced by the IC693CBL327 and IC693CBL328 cables, which have right-angle connectors to reduce the clearance space in front of the PLC.


Supported Modules:

    IC693MDL654
    IC693MDL655
    IC693MDL752
    IC693MDL753

These modules all have dual 24-pin connectors that require two cables per module.


Function of the Cable:

This prewired cable is specifically designed for Series 90-30 high-density I/O modules that utilize the Fujitsu 24-pin user I/O connector. Each of the modules has two 24-pin connectors mounted side-by-side. The I/O interface cable connects to the module with a 24-pin connector on one end, and on the other end, the wires are stripped and tinned for direct connection.

    The right connector on the module handles Groups A and B.
    The left connector handles Groups C and D.


Replacement Information:

    The IC693CBL315 cable was replaced by IC693CBL327 and IC693CBL328 due to the introduction of right-angle connectors. These new cables require less clearance space, making them more suitable for applications where space is limited.


Wire Pairing and Color Coding:

Here’s the wire pairing and color coding as outlined in the table:


Pin Number (A Row)    Pair #    Wire Color
A1    1    Black
A2    1    White
A3    2    Brown
A4    2    White
A5    3    Red
A6    3    White
A7    4    Orange
A8    4    White
A9    5    Yellow
A10    5    White
A11    6    Green
A12    6    White


Pin Number (B Row)    Pair #    Wire Color
B1    7    Blue
B2    7    White
B3    8    Violet
B4    8    White
B5    9    Gray
B6    9    White
B7    10    Brown
B8    10    Black
B9    11    Red
B10    11    Black
B11    12    Orange
B12    12    Black


Note on Wire Identification:

For proper identification, each pair of wires should be tied together with heat shrink tubing. For example, Pair #1 (Black and White wires) connecting to Pins A1 and A2 should be bound together.


Additional Information:

The IC693CBL327 and IC693CBL328 cables replaced the IC693CBL315 and IC693CBL310 cables. These newer versions, with their right-angle connectors, allow for more compact installations where space is limited in front of the PLC.

+  IC693CBL315 User manual (pdf)

>> Ge fanuc 90-30 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: IC693CBL315 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."