6ES7 193-1FL50-0XA0

6ES7193-1FL50-0XA0 Siemens ET 200L Single-Tier Spring Terminal

Siemens 6ES7 193-1FL50-0XA0 is a single-tier, 32-channel supplementary terminal with spring connections for the ET 200L system in the SIMATIC ET 200 family. It provides additional termination points for field wiring at the station. When identifying a replacement, distinguish the electronics block, the main terminal block and the supplementary terminal: each has a separate role in the ET 200 station assembly.

Specifications and purpose

The identifying features of 6ES7193-1FL50-0XA0 are ET 200L, 32 channels, one tier and spring terminals. Siemens lists an approximate component weight of 136 g. This is the part weight, rather than the shipping weight of a packaged assembly.

The 32-channel description refers to the terminal arrangement. The electronics block determines the station’s digital inputs and digital outputs. Adding this terminal does not create additional I/O addresses in the PLC; its job is to support the field wiring.

Understanding the common connection

The connections within the tier are internally linked. They must therefore be treated as a common electrical connection, not as isolated signal terminals. Determine the intended potential from the station wiring diagram and the terminal markings. Connecting different potentials to the same tier would join them electrically.

When tracing an inductive sensor cable, identify its supply, common and switched signal separately. Cable colour alone is not enough to decide where a wire belongs: compare the sensor diagram with the machine drawings. Selecting the power supply and checking the potential distribution are separate parts of that review. An electronic output module’s channel current rating should not be used as a rating for this supplementary terminal.

TB 32L assembly and similar part numbers

Siemens lists this part among the 32-channel supplementary terminals for TB 32L. The main terminal block and the electronics block fitted to it are separate components. Before ordering a replacement, compare the labels on the installed assembly, the retaining features and the direction of the field wiring. These checks are more useful than a visual resemblance alone.

6ES7193-1FL20-0XA0 is the single-tier screw-terminal version; 6ES7193-1FL60-0XA0 is the two-tier spring-terminal version. The 1FL50 described here has one tier and spring connections. Similar order numbers are not a substitute for checking the existing termination and mounting arrangement.

Installation and conductor preparation

The supplementary terminal fits into the guides beneath the main terminal block and locks in place. Siemens specifies 0.14–1.5 mm² conductors in the applicable wiring table and gives an 11 mm stripping length in its spring-terminal instructions. Where ferrules are used, their shape and length must also match the manual’s requirements.

Isolate the relevant circuits before installation. Check for a broken latch, cracked housing, damaged spring, exposed copper or an incorrect label left from earlier work. Allow enough room between the DIN rail power supply and field terminations to route conductors without strain. After replacement, compare the terminal identification with the drawings and check that each conductor is held securely.

Communication and fault finding

The ET 200L electronics block handles PROFIBUS communication and I/O data exchange. This supplementary terminal has no separate network address or program to load. If a field device is not operating, check its supply, assigned potential and wiring continuity before moving on to the electronic channel status and station diagnostics. The overview of ET 200 communication interfaces explains the network side of the system.

Manuals and technical documentation

Use the Siemens ET 200 user manuals and PDF documents page for wiring and installation references. Select the ET 200L documentation and its TB 16L/TB 32L supplementary-terminal, wiring and order-number sections. A terminal drawing from ET 200S or ET 200SP should not be applied just because it carries the same ET 200 family name.

Editorial note: Do not read “32 channels” as 32 isolated signal connections. Internal linking is the key detail when selecting this part or tracing a wiring fault. Preserve the intended PE/M identification and the potential arrangement shown in the machine drawings.

Related topics

Station wiring: ET 200 terminal blocks · connection modules · additional modules and accessories · power distribution components · power supply modules

Field devices and control: What is a PLC? · What is PROFIBUS? · digital input modules · digital output modules · sensors

These links explain the roles of related components. They do not establish mechanical compatibility between this terminal and parts from other ET 200 subfamilies.

Technical references: Siemens 6ES7193-1FL50-0XA0 data sheet (17 March 2017); ET 200L, ET 200L-SC and ET 200L-SC IM-SC manual, EWA 4NEB 780 6009-02c; ET 200L manual, EWA-4NEB 780600902-05. Numerical information applies to the identified part and the relevant document.

Navigation: Siemens Automation · Siemens S7 PLC · SIMATIC S7 · Siemens ET 200 · About ET 200 · ET 200 manuals