6ES7 157-0AD81-0XA0

6ES7 157-0AD81-0XA0 – Siemens DP/PA Coupler Ex [ia], 110 mA

6ES7 157-0AD81-0XA0 is a Siemens Ex [ia] DP/PA coupler connecting PROFIBUS DP to PROFIBUS PA. It includes an intrinsically safe PA supply and integrated barrier for connecting process field devices to the control system. See PROFIBUS and PROFINET for more about these networks.

Supply and PA capacity

The supply is 24 V DC, with a permissible range of 20.4–28.8 V DC. The PA output provides 13–14 V DC and a total of 110 mA maximum. Assess the manual’s 31-device PA limit alongside the combined current demand and cable voltage drop.

Stand-alone operation and DP/PA Link

For stand-alone operation, set the DP master to 45.45 kbit/s; the PA side operates at 31.25 kbit/s. The coupler requires no separate configuration. Configure and assign parameters to the PA field devices in the project.

A DP/PA Link connects the coupler to the higher-level network through an interface module. Check revision and system compatibility when reviewing the IM 153-2 interfaces used in this arrangement. For S7-300 projects, record the CPU model, DP master settings and installed Link hardware together.

PA termination and indicators

The Ex coupler’s integrated PA terminator cannot be switched off. The coupler must therefore be located at either end of the PA segment. Check the termination arrangement whenever changing the existing layout.

The front panel has a green ON LED and yellow DP and PA LEDs. Record their states alongside the connected-device list and measured supply values when investigating a fault.

Ex scope and installation location

For 0AD81, Siemens specifies intrinsically safe PA field devices for gas atmospheres in categories 1G/2G/3G, Zones 0/1/2. Assess the coupler’s own installation location separately. The manual requires a suitable approved enclosure with at least IP54 protection for Zone 2 installation.

Differences from 0AD82 and related models

The later 6ES7 157-0AD82-0XA0 additionally lists dust-atmosphere approvals for connected PA field devices. Siemens identifies 0AD82 as a compatible replacement for 0AD81. Check the unit’s nameplate, Ex documentation and segment design together when replacing it.

6ES7 157-0AC83-0XA0 is the FDC 157-0 DP/PA model with a PA output that is not intrinsically safe. 6ES7 158-0AD01-0XA0 is a DP/DP coupler for data exchange between two DP networks. Browse network interface modules for other options.

For a used unit, check that the full order number and Ex markings remain legible, and inspect the terminals and repair history. Ask which PA load and operating conditions were used to verify communication.

Editor’s Note: Keep a nameplate photograph, the existing PA device list and the segment drawing together when sourcing a spare for 0AD81. Match the Ex documentation to the complete order number. Compare the actual unit’s code and approvals with the quotation before purchasing.

Manuals and PDF documents

Use the Siemens ET 200 manuals section for documentation. Electrical values come from the exact-model table in DP/PA-Link et Y-Link, 02/2006, Section 13.3. The Ex variant distinction is documented in the 07/2011 manual, page 23, and replacement compatibility in the 12/2021 manual, page 280.

Control drawing A5E00151990-03 specifically covers 0AD81. Use it within its approval scope to check FISCO connections and match field-device safety parameters.

Related topics

Browse other system components under power supply modules, connection modules, terminal blocks, PLCs and modules and PLC and HMI.

Measurement products are listed under temperature sensors and pressure sensors. Verify PA communication support and Ex suitability against each selected device’s own model and documentation.

Navigation

Siemens ET 200 | Siemens SIMATIC S7 | Siemens automation | OtomasyonAVM home