6ES7 133-0HH00-0XB0

6ES7 133-0HH00-0XB0 – Siemens ET 200B 8DI/8RO-AC Input and Relay Output Module

6ES7 133-0HH00-0XB0 is the ET 200B-8DI/8RO-AC electronics block in the Siemens ET 200 family. It combines 8 AC digital inputs and 8 relay outputs, exchanging field data with the controller over PROFIBUS DP. This combined digital input and digital output device requires an ET 200B terminal block; it is not a direct replacement for an ET 200S or ET 200M module.

Supply and input characteristics

The electronics require 120/230 V AC, with a permitted range of 85–264 V AC at 47–63 Hz. The 120/230 V AC inputs are isolated in two groups of four and have a 0–25 ms input delay. Review the existing power supply arrangement and field signals accordingly; a 24 V DC input module is not electrically equivalent.

Temperature restriction: Above 40 °C in a 230 V AC installation, use at most six inputs, with input voltage no higher than 240 V AC.

Relay outputs and load limits

The relay outputs are individually isolated. Continuous-current limits are 4 A for Q0.0 and Q0.7 and 2 A for Q0.1–Q0.6; the ST 40 catalogue specifies a 16 A total switching-current limit. These figures do not apply equally at every switching voltage. For example, the manual specifies only 0.2 A switching capacity at 120 V DC. Check the contact ratings for the actual load type and temperature.

The outputs have no internal short-circuit protection. Select external protection for the load and wiring. Suitable suppression is also important for inductive loads such as contactor and valve coils. An illuminated channel LED alone does not prove that the relay contact is switching the load correctly.

An important output-voltage distinction

The rated output load is 120 V AC or 24–150 V DC. Another table in the manual mentions 120/230 V AC, creating an inconsistency. Therefore, 230 V AC load suitability requires manufacturer confirmation for the actual device label and revision. Do not infer the output rating from the input voltage.

Terminal block and communication

The compatible terminal block is TB6/AC. Match the terminal assignments to the complete electronics-block part number; physical fit alone does not establish identical wiring. PROFIBUS DP supports up to 12 Mbit/s, limited to 1.5 Mbit/s with IM 308-B. During commissioning, compare the station address, selected device definition and I/O addresses with the existing project.

Troubleshooting and replacement selection

A useful diagnostic approach separates the electronics supply, communication and load circuit. If communication is healthy but one output fails, inspect its external supply, fuse, wiring and relay contact first. When selecting a replacement, compare the full order number, terminal block, input voltage and load on every output. See the Siemens ET 200 overview for differences between system families. Isolate the relevant supplies and verify absence of voltage before removing or installing components connected to mains circuits.

Editor’s Note: “Eight inputs and eight outputs” is not enough to identify a suitable replacement. Check the AC input arrangement, relay contacts and individual loads together. For a used module, successful communication is only part of the assessment: contact operation under the intended load also matters. Never infer the output-voltage rating from the input rating.

User manuals and PDF documents

Use the Siemens ET 200 manuals and PDF documents page for technical references. This model is covered in Section 7.3.14, pages 7-89–7-94, of ET 200B Distributed I/O Station, EWA 4NEB 812 6089-02c. The ST 40 catalogue, page 4/12, also lists channel, current and terminal-block information.

Related topics

Explore other ET 200 options through special input modules, special output modules, analog and interface modules, function modules, counter modules, positioning modules, other network interfaces and additional modules and accessories. These sections cover different ET 200 subfamilies and are not a list of direct substitutes.

Navigation

Siemens ET 200 | Siemens SIMATIC S7 | Siemens automation | OtomasyonAVM home