6ES7 154-8FB01-0AB0
6ES7 154-8FB01-0AB0 is the Siemens IM 154-8F PN/DP fail-safe CPU for the SIMATIC ET 200pro system. It can execute a safety program alongside standard control applications. With 512 KB work memory and integrated PROFINET and PROFIBUS DP interfaces, it supports control tasks close to the machine. This model combines PLC functionality with a field-mounted design within the Siemens ET200 product family.
Product Description
The IM 154-8F PN/DP CPU can handle the control tasks of a machine section locally while communicating with a higher-level automation system. This arrangement is useful when organising conveyor sections, assembly stations or modular production equipment. During engineering, the responsibilities of standard control functions and safety functions, including their interaction, should be clearly defined.
The PROFINET interface supports IO Controller and I-Device functionality, while PROFIBUS DP can operate as a master or slave. The selected roles depend on the hardware configuration. For background information, see PROFIBUS and PROFINET explained. Related equipment is listed in the Siemens communication modules section.
Technical Data
Manufacturer: Siemens
Product family: SIMATIC ET 200pro
Order number: 6ES7 154-8FB01-0AB0
Product designation: IM 154-8F PN/DP CPU
Controller type: Fail-safe CPU for standard and safety applications
Work memory: 512 KB
Retentive data area: Up to 128 KB
Load memory: SIMATIC Micro Memory Card; up to 8 MB
Rated supply: 24 V DC
Permitted supply range: 20.4–28.8 V DC
PROFIBUS DP: Master/slave; up to 12 Mbit/s
PROFINET: Up to 100 Mbit/s; integrated 3-port switch
PROFINET connections: 2 × D-coded M12 and 1 × RJ45
Protection rating: IP65/IP67 with the required installation and sealing
Dimensions, W × H × D: 135 × 130 × 65 mm, including RJ45 cover
Approximate weight: 720 g
Safety Functions and the F-CPU Designation
The F in the product designation identifies the CPU version intended for safety applications. Manufacturer data specifies achievable levels of SIL 3 and PL e in a suitable system design. The machine’s safety performance depends on the complete combination of controller, field devices, wiring, program and validation.
For example, guard monitoring or an emergency stop function requires suitable sensors and appropriate inputs and outputs. When selecting digital input modules, digital output modules or analog input modules, verify ET 200pro compatibility and the required fail-safe capabilities. Connecting a standard I/O module to an F-CPU does not make that module suitable for safety functions.
Required Connection Module and Memory Card
A suitable SIMATIC Micro Memory Card is required for operation. Check separately whether the card and connection module are included in the supply. When purchasing a replacement CPU, review the existing program, card contents and hardware configuration together to identify any additional requirements before installation.
The model-specific Siemens product information specifies the CM IM PN DP M12, 7/8" connection module, order number 6ES7 194-4AN00-0AA0, from product version 03. Compare complete part numbers and versions when reviewing connection modules. The coding, pin assignment and environmental suitability of cables and connectors must also match the connection.
IP65/IP67 protection requires unused connections to be closed with suitable caps and seals to be correctly fitted. Refit the RJ45 cover after servicing. When examining used equipment, inspect the cover threads, sealing surfaces and connector pins as well as the enclosure itself.
Programming and Commissioning
The model-specific product information requires STEP 7 V5.5 or later for standard applications, with S7 Distributed Safety V5.4 SP4 or later additionally required for safety applications. The specified package for local F-modules is S7 F Configuration Pack V5.5 SP7 or later. Verify the chosen software combination against the existing project and CPU firmware version.
Before commissioning, back up the working project and record the CPU order number, firmware, PROFINET device name, IP address and PROFIBUS address. Compare the installed module sequence with the project. Following CPU replacement or changes to the safety program, complete the required acceptance and functional tests under the installation’s safety procedure. Reaching RUN mode does not demonstrate that all safety functions have been validated.
On the power supply side, distinguish the electronics/sensor supply 1L+ from the load supply 2L+. Size the power supply for the connected modules and loads as well as the CPU. Where power is distributed from a cabinet, select suitable DIN-rail power supplies and panel components for the specified protection and distribution arrangement.
Diagnostics and Maintenance
SF indicates a group fault, BF-DP a PROFIBUS fault, BF-PN a PROFINET fault and MAINT maintenance information. RUN/STOP indicators show the CPU operating state. Interpret flashing patterns together with the other indicators using the manual’s diagnostic tables.
During the initial investigation, read the diagnostic buffer and record the event sequence before attempting resets. If a fault concerns one station, examine its supply, device name, address and connections. For safety-related faults, compare F-parameters, module diagnostics and the approved project. Production must not continue with safety functions bypassed as a troubleshooting measure.
Practical Selection Notes and Related Products
For replacement selection, the designation “IM 154” alone is insufficient. The 8FB01 portion of the order number identifies this F version. The related 6ES7 154-8AB00-0AB0 standard CPU should not be treated as a direct replacement in an application requiring a safety program.
Providing a label photograph, connection-module code, firmware version and memory-card details helps assess suitability before quotation. Clarify the test scope as well: power-up, communication and program-execution checks are separate from acceptance of the machine’s safety functions.
User Manuals and PDF Documents
+ Siemens ET200 PLC User Manuals — PDF archive page.
+ Siemens IM 154-8F CPU — Model-Specific Product Information — F-CPU features, software requirements and connection-module requirements for 6ES7 154-8FB01-0AB0.
+ Siemens IM 154-8 PN/DP CPU Operating Instructions — installation, communication and diagnostics; use together with the F-version supplement above.
+ Siemens 6ES7 154-8FB01-0AB0 Technical Data Sheet — an externally hosted copy of the Siemens document.
+ Siemens ET200 General Catalogue — general product-family reference.
++ Siemens Automation Main Page >
++ Siemens Product Enquiries — contact Otomasyon AVM.
++ About Siemens ET200 PLC Systems >
Reminder: Confirm current availability, condition and delivery contents with Otomasyon AVM for the Siemens 6ES7 154-8FB01-0AB0 and other SIMATIC PLC products. Some items are used equipment; take this into account before purchasing. Products will not be restocked once sold out. This page provides general information; check the product label, hardware version and applicable manufacturer documentation for your installation.
Note: Manuals, commissioning suggestions and troubleshooting descriptions are provided for reference and are not binding. Content may be updated or expanded. The Otomasyon AVM Community welcomes practical feedback. You can share your operating and maintenance experience with us.
Technical references: Siemens 6ES7154-8FB01-0AB0 data sheet; IM 154-8F CPU Product Information, A5E02881798-03; IM 154-8 PN/DP CPU Operating Instructions, A5E00860134-02. Consult the product-information supplement for differences specific to the F version.