6ES7 153-2BA01-0XB0

Siemens 6ES7 153-2BA01-0XB0 – ET 200M IM 153-2 High Feature Interface Module

6ES7 153-2BA01-0XB0 is an IM 153-2 High Feature interface module for the ET 200M distributed I/O system in the Siemens SIMATIC ET200 family. It connects compatible S7-300 I/O modules to a higher-level PLC system over PROFIBUS DP. Typical uses include process plants, production lines and distributed stations within redundant control systems.

The compact article number is 6ES7153-2BA01-0XB0. When selecting a replacement, check the 2BA01 version, hardware label and configured module entry together with the IM 153-2 family name.

Its role within ET 200M

The module operates as a slave on PROFIBUS DP and transfers data between the master system and compatible S7-300 modules installed to its right. Field signals are handled by the corresponding input modules, while output commands are applied through the output modules. The IM 153-2 manages their communication with the controller.

This arrangement allows automation equipment to be distributed across local control cabinets. The station's digital input modules, digital output modules and analog input modules must be suitable S7-300 versions approved for ET 200M.

Main technical characteristics

Product designation: IM 153-2 High Feature
Article number: 6ES7 153-2BA01-0XB0
Communication: PROFIBUS DP, RS 485
Connector: 9-pin Sub-D
Maximum transmission rate: 12 Mbit/s
PROFIBUS address range: 1 to 125
Rated supply: 24 V DC
Permissible supply range: 20.4 to 28.8 V DC
I/O module capacity: Up to 8 modules
Address space: 128 bytes of inputs and 128 bytes of outputs
Dimensions, width × height × depth: 40 × 125 × 117 mm
Approximate weight: 350 g
Degree of protection: IP20.

The capacity difference between BA01 and BA02

6ES7 153-2BA01-0XB0 supports a maximum of 8 modules. The 12-module capacity available with later versions such as 2BA02 should not be attributed to this model. Spare cabinet space alone does not establish that an existing interface can support additional modules.

Total input and output address space must also be calculated. When planning a change to another communication interface, assess the master, engineering software, bus base and installed I/O cards together.

Redundancy and active bus hardware

The IM 153-2BA01 supports a redundant PROFIBUS DP connection in an appropriate configuration. This arrangement uses two compatible IM 153-2 modules on a suitable BM IM/IM bus module, with the redundant master system configured accordingly.

Siemens compatibility tables identify the 6ES7 195-7HD10-0XA0 BM IM/IM bus module for this version. The complete arrangement also requires the appropriate rail, active bus components and interface pair. Full article numbers are therefore important when selecting connection modules.

Replacing I/O modules during operation

I/O module replacement during operation requires a station built with suitable active bus modules and the mounting rail designed for this function. A station assembled with standard bus connections should not automatically be assumed to provide the same capability.

Maintenance planning should identify the card being replaced, the state of the connected process and the configured fault responses. This helps establish whether removing a card will affect individual channels or a wider part of the installation.

Time stamping and isochronous operation

With suitable digital input modules and time synchronization, the interface can be used for time stamping with 1 ms precision. This is useful when investigating the order of closely spaced input transitions in a plant. The applicable performance depends on the signal module and system configuration.

Isochronous operation is also supported. The master, I/O modules and engineering settings must support the required operating arrangement. Time stamping and isochronous operation are separate functions with their own configuration requirements.

Mounting, power and PROFIBUS cabling

ET 200M can be installed horizontally or vertically. For the standard arrangement, the manufacturer's manual specifies ambient ranges of 0 to 60 °C for horizontal installation and 0 to 40 °C for vertical installation. Cabinet layout, ventilation and the requirements of the other installed modules must also be considered.

The power supply, cable shielding and grounding arrangement influence communication reliability. Check the PROFIBUS connector wiring and bus termination against the station's position in the network.

Commissioning and fault investigation

Select the correct IM 153-2 version in STEP 7 hardware configuration or use the appropriate GSD file. Compare the physical module sequence, configured card order, PROFIBUS address and I/O addresses. If the module is missing from the hardware catalog, check the engineering software's installed hardware support.

For communication interruptions, begin with the supply, address, cabling and termination, then assess the master's diagnostics and station module information. In a redundant arrangement, include both communication paths and the active bus connections. This helps distinguish an interface fault from a wiring or configuration problem.

PDF manuals and technical documentation

Browse our Siemens ET200 manuals and PDF documentation page for related documents. For this product, read the ET 200M manual sections covering IM 153-2BA01, the compatibility tables and the documentation for the installed S7-300 cards together.

Editor's note: The eight-module limit and the station's active bus arrangement are particularly important when selecting this interface. Recording the IM label, bus module article numbers and STEP 7 hardware configuration before replacement makes the correct spare easier to identify.

Related product groups

For other station components, explore ET200 power supply modules, power distribution modules, additional modules and other network interfaces. Confirm ET 200M compatibility separately for each selected component.

Explore: About ET200 | SIMATIC S7 | Siemens S7 PLC products