6ES7 141-1BF12-0XB0
Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7141-1BF12-0XB0
Siemens 6ES7 141-1BF12-0XB0 — ET 200X BM 141, 8 Digital Inputs
The 6ES7 141-1BF12-0XB0 is an ET 200X BM 141 basic module in the Siemens ET 200 family. It has 8 inputs, 24 V DC and integrated PROFIBUS-DP. When selecting ET 200 digital input modules, account for the basic module's station communication role as well.
Distinguish basic and expansion modules
BM 141 handles the station's PROFIBUS connection alongside its field inputs. When recording the ET 200 station configuration, identify the basic module, attached expansion modules and their physical sequence separately. “Eight-input module” alone is insufficient to identify the correct replacement.
When comparing PROFIBUS and PROFINET interfaces, this product uses PROFIBUS-DP at up to 12 Mbit/s. Compare communication settings with the device selection and address in the existing PLC project; matching physical connections do not establish correct configuration.
Input levels and response time
“1” level: 13–30 V; “0” level: −3…+5 V. Input delay: 1.2–4.8 ms in both transition directions. Compare the sensor's active and inactive electrical values as well as its supply rating. Consider ET 200 analog input modules separately for devices providing continuous measurement signals.
Eight inputs through four M12 sockets
X1–X4 pin 4: channels 0–3 respectively; pin 2: channels 4–7 respectively. Account for this two-input arrangement when selecting ET 200 connection modules and accessories. Connecting one sensor cable to a socket does not mean both inputs at that socket are in use.
If a splitter or adapter is fitted, label the input assigned to each branch. Do not match ET 200 terminal blocks and connection parts from different series by appearance. Including socket number, pin, channel and PLC address on the same drawing helps prevent tracking the wrong sensor during maintenance.
Replacing 1BF11 with 1BF12
Siemens' SIMOTION compatibility list identifies 6ES7141-1BF12-0XB0 as the successor to 6ES7141-1BF11-0XB0. That listing does not remove the need to check the existing project. Review hardware-catalog or GSD selection, diagnostic settings and compatibility with attached expansion modules together.
Five checks before selection or replacement
1. Label and release: Record the complete order number and product release. Keep the basic-module label and a photograph of the complete station in the same maintenance record.
2. Supply arrangement: Compare ET 200 power supply modules and ET 200 power distribution components against the existing drawings. Track the electronics/sensor supply separately from the station's load supply; voltage on one does not establish that the other is healthy.
3. Signal mapping: Operate each sensor individually and verify its input address. Keep commands from ET 200 digital output modules and sensor feedback in separate lists.
4. Network and project: Back up the PROFIBUS address, termination arrangement, module sequence and selected device definition. If several changes are required, use a test sequence that allows their individual effects to be identified.
5. Replacement and connection checks: Siemens' service checklist requires the 24 V supply to be switched off before module replacement. Check caps on unused sockets and connection sealing, then test the inputs under controlled conditions.
Editor's note: Four sockets do not mean four inputs. First distinguish the separate signals on pins 2 and 4 when troubleshooting this model. Comparing the sensor LED, module input state and PLC address together helps separate a wiring problem from a program or module fault.
Manuals and PDF documents
On the Siemens ET 200 PDF and user manuals page, consult ET 200X, EWA 4NEB 780601602-06, section 7.1 for this model. Also check the corrected circuit diagram in Siemens supplement A5E00125915-05.
Related topics
Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules
Explore the station: About ET 200 · Communication interfaces · ET 200 manuals
Otomasyon AVM | Siemens:
Siemens main menu | Siemens S7 PLC | SIMATIC S7 | ET 200 modules