6ES7 135-4LB02-0AB0

Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7135-4LB02-0AB0

Siemens 6ES7 135-4LB02-0AB0 ET 200S 2AO U High Feature Analog Output Module

6ES7 135-4LB02-0AB0 is a two-channel analog voltage output module for ET 200S. Designated 2AO U High Feature, it is 15 mm wide and has a 0.5 ms cycle time per module. Within Siemens ET 200 distributed I/O systems, it can provide reference signals to devices with compatible voltage inputs.

Output range and resolution

The Siemens product description specifies 15 bits plus sign for ±10 V and 15 bits for 1–5 V. The receiving drive or controller must use an input range matching the PLC configuration. A voltage output cannot directly provide a suitable signal to a 4–20 mA input; check the receiving device's input type before wiring.

ET 200 analog input modules used to monitor the process perform a separate measurement function. For example, a speed reference and actual motor speed feedback should be treated as separate signals in the project.

Two-wire and four-wire connections

The module supports two-wire and four-wire connections; two-wire wiring does not compensate for line resistance. Load impedance must be at least 1 kΩ, with a capacitive load of no more than 0.5 µF. When selecting ET 200 connection components, consider cable length, shielding and the receiving device's input impedance together.

Use the S+ and S− sensing terminals according to the four-wire connection diagram. Measuring at the receiving input as well as at the module helps identify voltage differences along the cable.

Terminal module and power arrangement

Suitable ET 200 terminal modules include TM-E15S24-01 / 6ES7193-4CB20-0AA0 and TM-E15C24-01 / 6ES7193-4CB30-0AA0. The module receives 24 V DC from the power module. Record the existing potential group and terminal arrangement when reviewing ET 200 power supply modules and power distribution components. The two output channels are not galvanically isolated from each other.

Five checks before selection or replacement

1. Exact model and function: Verify 6ES7135-4LB02-0AB0 on the label. Distinguish the switching function of ET 200 digital output modules from this module's continuously variable voltage reference.

2. Scaling: The PLC value, configured voltage range and physical quantity at the receiving device must use a consistent relationship. Check lower, midpoint and upper reference values during commissioning.

3. Wiring: Compare the terminal module number, two-wire or four-wire arrangement and common reference. Label conductors and photograph the connections before transferring existing wiring to a replacement.

4. STOP response: CPU/master STOP options include zero output, substitute value and hold last value. When reviewing the ET 200 system architecture, determine what the selected response means for the machine. Check digital input signals, such as drive enable feedback, alongside the analog reference.

5. Interface and diagnostics: For stations using PROFIBUS and PROFINET interfaces, confirm that the hardware project matches the installed module. If the SF group fault LED illuminates, read the diagnostic record before concluding that the electronic module is defective.

Editor's note: An apparent analog output fault may originate in the receiving device's input range or an incorrect common reference connection. Before replacing the module, record the PLC command, voltage at the module and voltage at the receiving input under the same operating condition. Together, these readings make the source of the discrepancy easier to locate.

Manuals and PDF documentation

Visit the Siemens ET 200 PDF documentation and user manuals page for the relevant resources. For this product, consult the terminal, parameter, analog representation and connection sections of 2AO U HF analog electronic module — 6ES7135-4LB02-0AB0, manual A5E01076940-01.

Related topics

Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules

Explore the station: About ET 200 · Communication interfaces · ET 200 manuals

Otomasyon AVM | Siemens:
Siemens main menu  |  Siemens S7 PLC  |  SIMATIC S7  |  ET 200 modules