6ES7 138-4DK00-0AB0

Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7138-4DK00-0AB0

Siemens 6ES7 138-4DK00-0AB0 — ET 200S 1PosSSI/Analog Positioning Module

The 6ES7 138-4DK00-0AB0 is an ET 200S 1PosSSI/Analog positioning module in the Siemens ET 200 family. It uses SSI absolute encoder feedback and an analog drive command for one axis. It belongs to the ET 200 function module range. The motor power circuit connects to the drive; this module provides the drive command signal.

Technical configuration and signal options

Supply: 24 V DC, permitted range 20.4–28.8 V DC. Encoder: 13-bit singleturn or 25-bit multiturn SSI. Analog command: ±10 V, or 0–10 V with a digital direction signal. Auxiliary I/O: 3 digital inputs, 1 digital output. Housing: 30 × 81 × 52 mm.

Which terminal base is used?

Siemens' commissioning example specifies a TM-E30S44-01 base, order number 6ES7193-4CG20-0AA0 or 6ES7193-4CG30-0AA0. When selecting ET 200 terminal blocks, compare the complete base number and terminal arrangement as well as its 30 mm width. Similar-looking ET 200 connection modules may have different terminal assignments.

How do DK00, DJ00 and DH00 differ?

6ES7138-4DK00-0AB0: SSI/Analog. 6ES7138-4DJ00-0AB0: INC/Analog. 6ES7138-4DH00-0AB0: SSI/Digital. Address two separate questions when selecting a replacement: Which signal does the encoder provide, and which command does the drive require? Membership of the same ET 200S family does not establish direct interchangeability.

Check the station and field equipment together

Identify the ET 200 power supply module from the existing panel design and record its relationship with the power distribution components. When reviewing the ET 200 station configuration, keep the CPU program, module parameters and exact PROFIBUS or PROFINET interface order number together. A shared protocol name alone is insufficient to establish interface compatibility.

Distinguish auxiliary field signals wired to this module from those connected to separate ET 200 digital input modules. Likewise, identify the ET 200 digital output modules used for drive enables and other commands on the panel drawings. This keeps position feedback, analog reference and auxiliary commands clearly identified during replacement.

Five checks before selection or replacement

1. Module identity: Confirm 6ES7138-4DK00-0AB0 on the label. Compare the encoder and drive interfaces before considering DJ00 or DH00 as an alternative.

2. Encoder compatibility: Record the complete encoder model, supply, SSI data format, resolution and clock frequency. Matching connectors do not establish electrical compatibility; check cable length against the selected frequency too.

3. Drive command: Verify the drive's analog input range, direction control method and signal common. The parameters and field wiring must use the same command arrangement.

4. Position scaling: Compare the mechanical transmission ratio, encoder resolution, direction of travel and target-value units. After replacing an encoder, do not assume that the original parameters still represent the same physical distance.

5. Replacement and testing: Siemens requires the load voltage to be switched off externally before inserting or removing the 1PosSSI/Analog. Perform the first movement under controlled conditions, checking direction, position readings, limits and stopping behaviour.

Editor's note: When diagnosing a positioning problem, consider more than the module itself. Incorrect encoder parameters, analog reference settings or mechanical backlash can also cause poor stopping accuracy. Recording the module, encoder and drive labels together with the existing parameters helps both replacement selection and fault isolation.

Manuals and PDF documents

On the Siemens ET 200 PDF and user manuals page, consult ET 200S Positioning — A5E00124871-04. Chapter 6: 1PosSSI/Analog covers the product, wiring, parameters and technical data. Also consult the ET 200S operating instructions for general installation and module replacement.

Related topics

Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules

Explore the station: About ET 200 · Communication interfaces · ET 200 manuals

Otomasyon AVM | Siemens:
Siemens main menu  |  Siemens S7 PLC  |  SIMATIC S7  |  ET 200 modules