6ES7 138-4DA04-0AB0
Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7138-4DA04-0AB0
Siemens 6ES7 138-4DA04-0AB0 — ET 200S 1Count 24 V/100 kHz Counter Module
The 6ES7 138-4DA04-0AB0 is a single-channel, 32-bit, 24 V/100 kHz counter module for ET 200S, part of the Siemens ET 200 family. It is 15 mm wide. Within the ET 200 function module range, it provides counting, frequency, rotational-speed and period measurement, with isochronous mode support.
Input signals and the 100 kHz limit
Supported signals include 24 V pulses, pulses with direction and A/B encoder signals offset by 90°. 100 kHz is the frequency limit of the A/B signals. The 400,000 counts/s obtained with quadruple evaluation does not mean that a 400 kHz input is permitted. Check encoder supply voltage separately from the electrical output type.
Supply and auxiliary I/O
Supply: 24 V DC, operating range 20.4–28.8 V DC. Dimensions: 15 × 81 × 52 mm. In addition to the counting inputs, the module has one auxiliary digital input and one physical digital output. The auxiliary input supports gate control, synchronization or a latch function.
As with ET 200 digital output modules, consider temperature when selecting the output load. The specified output current is 2 A at 40 °C, 1 A at 50 °C and 0.5 A at 60 °C. A “2 A output” description alone is insufficient for load selection.
Terminal bases and replacement of DA03
Siemens specifies TM-E15S24-01 and TM-E15S26-A1 bases. Use the complete base designation when comparing ET 200 terminal blocks and ET 200 connection components. The manual identifies DA04 as a fully compatible replacement for 6ES7138-4DA03-0AB0; retain the existing project and parameter records during replacement.
Selecting the module within the station
Record the ET 200 power supply module and power distribution arrangement on the panel drawings. When reviewing the ET 200 station configuration, consider the CPU, interface, software and operating mode together. Check the relevant model requirements when selecting PROFIBUS and PROFINET interfaces, particularly for isochronous operation.
Assigning high-speed pulses to this counter and other field states to suitable ET 200 digital input modules makes the project easier to review. Treat signal counting, transfer of measured values to the PLC and use of those values in the program as separate stages; the PLC scan time alone does not describe the whole process.
Five checks before selection or replacement
1. Exact model and signal: Confirm 6ES7138-4DA04-0AB0 on the label. An encoder powered from 24 V does not necessarily provide 24 V output signals; verify its output type in its own data sheet.
2. Maximum pulse frequency: Calculate the input frequency from the encoder pulses per revolution and the machine's maximum speed. Then check whether single, double or quadruple evaluation is configured.
3. Filter and cable: Select the input filter for the actual pulse duration. Excessive filtering can suppress short pulses, while inadequate shielding can cause false counts. Compare cable length and shield connections with the manual requirements.
4. Parameters: Record count direction, initial value, gate behaviour, comparison values and measurement scaling. Identical-looking modules do not establish that a new project's parameters match the original machine.
5. Verification: Apply a known number of pulses and check the result. With an encoder, verify the count and direction over one controlled revolution, then test at an appropriate operating speed.
Editor's note: An encoder producing 1,024 periods per revolution on channel A generates 51.2 kHz at 3,000 rpm: 1,024 × 3,000 / 60. Quadruple evaluation produces 204,800 counts/s. Keeping input frequency separate from the evaluated count rate helps prevent both selection and scaling errors.
Manuals and PDF documents
On the Siemens ET 200 PDF and user manuals page, consult the 1Count24V/100kHz chapter of ET 200S Technological Functions — A5E00124867-06. It covers terminal connections, counting and measurement modes, parameters and timing. Check the technical limits alongside the 6ES7138-4DA04-0AB0 data sheet.
Related topics
Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules
Explore the station: About ET 200 · Communication interfaces · ET 200 manuals
Otomasyon AVM | Siemens:
Siemens main menu |
Siemens S7 PLC |
SIMATIC S7 |
ET 200 modules