6ES7 132-7HB00-0AB0

Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7132-7HB00-0AB0

Siemens 6ES7 132-7HB00-0AB0 — ET 200iSP 2 DO Relay Output Module

6ES7 132-7HB00-0AB0 is the ET 200iSP 2 DO Relay UC60V/2A electronic module in the Siemens ET 200 family. Its two normally open (NO) relay outputs switch suitable valve, contactor and indicator circuits. When selecting ET 200 digital output modules, assess relay contacts and electronic outputs according to their different load characteristics.

Understanding UC 60 V / 2 A

UC indicates AC/DC operation. The 2 A rating does not mean identical switching capability at every voltage and load type. Siemens lists operating points of 24 V DC / 2 A and 60 V AC / 2 A in its contact-load table, while the 60 V DC entry specifies 0.5 A. Select the module with reference to load type, switching frequency and required contact life.

Outputs: 2. Short-circuit protection: none. Parallel connection for increased current or redundant load control is not permitted. The module cannot diagnose wire breaks or short circuits in the contact power circuit. Green LEDs indicate channel status; a red SF LED indicates a group fault. Dimensions: 30 × 129 × 136.5 mm.

Terminal base and field wiring

The module uses the TM-RM/RM 60S — 6ES7193-7CB00-0AA0 base, which accommodates two relay modules. Use this pairing when selecting ET 200 terminal blocks and ET 200 connection modules. Do not assume that an ET 200S base or another ET 200iSP terminal type is interchangeable because it looks similar.

The base's Ex e screw terminals and Ex d disconnecting plug are part of the installation arrangement. Keep the terminal cover closed during operation. Do not automatically treat the relay field circuit as intrinsically safe; check the connected device's protection type and certificate conditions. Isolate the contact load voltage before wiring and follow the specified disconnecting-plug sequence for module removal and insertion.

Reviewing the complete station

When recording the ET 200 station configuration, identify the exact PROFIBUS or PROFINET interface. Permitted slot positions depend on the interface and redundancy arrangement. Match the ET 200 power supply modules and power distribution connections to the wiring diagram, tracing the electronic module supply separately from the load circuit switched by its contacts.

If a valve or contactor provides status feedback, identify the corresponding ET 200 digital input modules. Comparing this feedback with pressure or level readings from ET 200 analog input modules can help explain why the process fails to respond to an output command.

Five checks before selection or replacement

1. Exact model: Verify 6ES7132-7HB00-0AB0 on the label. Do not plan a direct substitution with a four-output electronic module from the 7RD series.

2. Load details: Record AC/DC type, voltage, continuous current and inrush current. Assess suitable suppression for coil loads.

3. Terminal and Ex conditions: Check the base code, cover, disconnecting plug, field-device certification and cable arrangement together.

4. CPU STOP response: Verify whether the application requires retaining the last value or applying a substitute value. The substitute value can be 0 or 1 for each channel.

5. Functional checks: Check the contact circuit and actual load response as well as the channel LED. Include external protective devices in the maintenance record.

Editor's note: If the output LED is on but the valve does not operate, examine the load supply, fuse, contact, field cable and coil in sequence. The LED alone does not prove that the load is receiving power.

Manuals and PDF documents

Visit the Siemens ET 200 PDF and user manuals page and consult the 2 DO Relay UC60V/2A section of the ET 200iSP operating instructions together with product information A5E01223637-01. Review contact life, load ratings, terminal installation and Ex conditions together.

Related topics

Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules

Explore the station: About ET 200 · Communication interfaces · ET 200 manuals

Otomasyon AVM | Siemens:
Siemens main menu  |  Siemens S7 PLC  |  SIMATIC S7  |  ET 200 modules