6ES7 132-4BF00-0AA0
Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7132-4BF00-0AA0
Siemens 6ES7 132-4BF00-0AA0 — ET 200S 8 DO, 24 V DC / 0.5 A
6ES7 132-4BF00-0AA0 is an eight-channel digital output module for ET 200S in the Siemens ET 200 family. Its 24 V DC PNP sourcing outputs control suitable valves, DC contactors and indicators. Among ET 200 digital output modules, it offers eight channels in a 15 mm width, rated at 0.5 A per channel and 4 A total per module.
Output capacity and protection
Connecting two outputs in parallel to increase current capacity is not permitted. The lamp-load limit is 5 W, and off-state residual current is at most 0.3 mA. Consider this residual current when connecting a low-power electronic input or indicator; a voltage measured at an inactive output does not by itself prove a fault.
Short-circuit protection is provided; diagnostic functions are not. A green LED indicates each channel's output state. During maintenance, check the load supply, wiring and actual actuator response as well as the LEDs and PLC display.
Terminal base and channel order
Compatible base examples include TM-E15S26-A1 / 6ES7193-4CA40-0AA0 with screw terminals and TM-E15C26-A1 / 6ES7193-4CA50-0AA0 with spring terminals. Select ET 200 terminal blocks by their complete order codes. Similar-looking ET 200 connection modules do not necessarily have the same terminal assignments.
Channel-to-terminal mapping: DO0→1, DO1→5, DO2→2, DO3→6, DO4→3, DO5→7, DO6→4, DO7→8. Two-wire loads may require additional M return terminals; plan these using suitable ET 200 power distribution components. Eight outputs should not be mistaken for eight complete two-wire terminal pairs.
Interface and station planning
When reviewing PROFIBUS and PROFINET interfaces, record the model and firmware together. For example, the manual's operating-requirements table lists 6ES7151-1AA03-0AB0 for IM 151-1 STANDARD and 6ES7151-3AA20-0AB0 with V4.0.1 for IM 151-3 PN as starting requirements. Check the installed interface's full code against that table.
When planning the ET 200 station configuration, include every load served by the ET 200 power supply modules. For example, eight loads drawing 0.4 A each produce a 3.2 A load total for this module alone. Add the other modules in the same supply group separately.
Match valve or contactor feedback to the corresponding ET 200 digital input modules. If an output triggers a counter or another ET 200 function module, assess power-up behaviour as well as normal operation.
Five checks before selection or replacement
1. Exact model: Verify 6ES7132-4BF00-0AA0 on the label. Do not select an input module, relay output or different suffix solely by channel count.
2. Load calculation: Check continuous and inrush current per channel, simultaneous loads and the complete supply-group total.
3. Wiring: Compare channel order with the terminal mapping above. Record M returns and shared supply connections.
4. Hardware configuration: Match the interface code, firmware and PLC output addresses to the existing project.
5. Functional testing: Operate loads individually under controlled conditions. Compare LED state, voltage across the load and mechanical response.
Editor's note: Siemens notes that applying the 24 V load supply to the power module through a mechanical contact can produce an approximately 50 µs “1” signal at the outputs. Consider this behaviour when investigating an extra count at power-up in applications connected to high-speed counter inputs.
Manuals and PDF documents
Visit the Siemens ET 200 PDF and user manuals page and consult 8DO DC24V/0.5 A — A5E01077385-AB. This model-specific manual covers terminal assignments, interface requirements and electrical limits; the ET 200S operating instructions cover general installation requirements.
Related topics
Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules
Explore the station: About ET 200 · Communication interfaces · ET 200 manuals
Otomasyon AVM | Siemens:
Siemens main menu |
Siemens S7 PLC |
SIMATIC S7 |
ET 200 modules