6ES7 151-7FA01-0AB0

Siemens 6ES7151-7FA01-0AB0 – ET 200S IM151-7 F-CPU

Siemens 6ES7151-7FA01-0AB0 is the IM151-7 F-CPU fail-safe controller for SIMATIC ET 200S. It provides local program execution and safety-related control functions. Within the Siemens ET 200 family, it is a CPU-equipped model with an integrated MPI/PROFIBUS DP communication interface.

Memory, power supply and physical dimensions

The CPU has 64 KB of work memory. Its rated supply is 24 V DC, with a permissible range of 20.4–28.8 V DC. Housing dimensions are 60 × 119.5 × 75 mm, stated as width, height and depth.

A SIMATIC Micro Memory Card (MMC) provides load memory, and the controller operates without a battery. MMC capacity and work memory are separate specifications: a larger card does not expand the 64 KB work memory. Back up the project and card contents before maintenance, and do not remove the MMC while the CPU is in RUN.

MPI, PROFIBUS DP slave and master operation

The integrated 9-pin female Sub-D connector provides MPI or PROFIBUS DP communication. On PROFIBUS, the CPU can operate as an intelligent DP slave connected to a higher-level controller while executing its own local program. This model has no integrated Ethernet/PROFINET port.

The optional 6ES7138-4HA00-0AB0 DP master module allows the station to control downstream PROFIBUS devices. The integrated DP slave interface and the additional DP master interface perform separate roles. For network and system information, see ET 200 PROFIBUS and PROFINET.

Programming and safety applications

The Siemens data sheet specifies STEP 7 V5.2 SP1 or later and S7 Distributed Safety V5.2 SP1 or later for safety programming. Check the engineering software, hardware catalog and CPU firmware against the existing project.

For safety applications, review the CPU together with the PROFIsafe architecture and appropriate ET 200 safety modules. Safety validation includes sensors, actuators, wiring, software and response times. An F-CPU alone does not establish a particular machine safety level.

Important F-module compatibility requirements

For the PM-E F pp DC24V PROFIsafe power module 6ES7138-4CF40-0AB0, Siemens specifies CPU firmware V2.1.4 or later when used with this CPU. Selection therefore requires the complete order number and installed firmware, rather than the IM151-7 F-CPU designation alone.

For central operation of the EM 4 F-DI/3 F-DO DC24V PROFIsafe module directly behind an IM151-7 F-CPU, Siemens specifies 6ES7151-7FA20-0AB0 with firmware V2.6 or later. This central configuration support must not be attributed to 6ES7151-7FA01-0AB0. Operation through a separate distributed station requires its own interface and system compatibility assessment.

FA01 hardware and firmware upgrade limitations

Siemens product information explicitly states that 6ES7151-7FA01-0AB0 hardware cannot be upgraded to the V2.6 firmware of the newer IM151-7 CPU generation. Consequently, FA20-generation features cannot be added to FA01 simply by loading firmware. A hardware migration requires review of the controller, safety program and connected modules.

Commissioning and fault diagnosis

During commissioning, check the MPI/PROFIBUS address, transmission rate, master-side data areas and ET 200S module sequence. Include the PROFIBUS cable, shield connection and segment-end termination in the inspection. Read the SF/BF indications together with the STEP 7 diagnostic buffer; a communication fault alone does not establish that the CPU is defective.

PDF documentation and user manuals

For documentation references, visit the Siemens ET 200 user manuals and PDF documentation page. Select documents applicable to 6ES7151-7FA01-0AB0 and review the IM151-7 CPU manual, F-CPU product information and documentation for the installed F-modules together.

Related topics

Input and output modules: Digital input modules, digital output modules, analog input modules, special input modules and special output modules.

Power and connections: Power supply modules, power distribution modules, terminal blocks and connection modules.

Functions and expansion: Functional and safety modules, counter modules, positioning modules, additional modules and other network interface modules. For a system overview, see About Siemens ET 200.

These sections may include different ET 200 subfamilies. Compatibility with this CPU must be verified using the complete module order number and version information.

Navigation: Siemens Automation | Siemens S7 PLC | SIMATIC S7 | SIMATIC ET 200