6ES7 953-8LF11-0AA0
6ES7 953-8LF11-0AA0 — Siemens SIMATIC Micro Memory Card 64 KB
Series: Siemens SIMATIC S7. Category: SIMATIC Micro Memory Card (MMC), 64 KB memory card.
6ES7 953-8LF11-0AA0 is a 64 KB, 3.3 V NFlash memory card for suitable S7-300, C7 and ET 200S IM151 CPU applications with an MMC slot. In CPU applications, it provides nonvolatile load memory for the program and system data. Check the complete device order number and supported MMC version before selecting the card.
What does the 64 KB capacity mean?
Card capacity is separate from the CPU’s work memory. A larger MMC does not increase the processor’s RAM capacity or program execution speed. Determine whether 64 KB is sufficient by checking the total load-memory requirements of code blocks, data blocks and system data in STEP 7. The size of the project folder on a computer is not a sufficient selection criterion.
The IM151-7 CPU uses the MMC as its load memory and requires a card for operation. However, having a program on the card does not mean that every current process value is automatically backed up there. Retentive behavior must be assessed together with the CPU and data-block settings.
Different roles in ET 200 interfaces
An MMC does not perform the same job in every ET 200 device. For example, the manual for IM151-3 PN FO, 6ES7 151-3BB22-0AB0 specifies that 64 KB is sufficient to store the PROFINET device name. Updating that interface’s firmware via a card requires at least 2 MB, so this 64 KB model is insufficient for that operation.
This distinction matters when assessing PROFIBUS and PROFINET systems and network interfaces. Inserting an MMC does not give an interface CPU functionality. Check the complete device code and intended operation rather than relying on the “ET 200” or “IM151” family name.
Capacity differences between related cards
In the same order-number group, 6ES7 953-8LG11-0AA0 provides 128 KB, 6ES7 953-8LJ11-0AA0 provides 512 KB and 6ES7 953-8LL11-0AA0 provides 2 MB. The 8LF11 model on this page is 64 KB. A larger card still needs to match the CPU’s supported cards and the application requirements. Ordinary consumer SD/MMC cards are not direct equivalents.
Programming, formatting and replacement
Do not format the card using Windows. Siemens warns that this can overwrite its SIMATIC-specific internal structure and make it unusable in an S7 CPU. Use suitable Siemens programming hardware, supported software or the device’s own interface for reading and writing. A computer’s format prompt does not establish that the card is empty.
Back up the existing program and configuration before replacing the card, and carry out replacement with device power switched off. Do not remove the card in RUN or during a write operation. Inspect its orientation, contacts and slot, then verify the program and hardware configuration before restarting the CPU. Deleting card contents, resetting CPU memory and formatting the card are different operations.
Editor’s note: Do not test a used MMC by inserting it directly into a running machine. Preserve the existing card contents and project backup first. The replacement may contain another machine’s program or device name. A 64 KB label identifies capacity; it does not prove that the contents are correct or that the card is healthy.
PDF documentation and manuals
Read the memory concept and card replacement sections of the IM151-7 CPU manual alongside the MMC instructions for the actual interface. Visit the Siemens ET 200 PDF and user manuals page for documentation.
Related topics
Within an ET 200 system, digital inputs, digital outputs and function modules must match the project configuration. Include any program blocks required for counter modules and positioning modules in the memory calculation. Suitability for safety modules and PROFIsafe cannot be established through memory-card selection alone.
The power supply, power distribution, terminal blocks and connection components complete the station’s hardware. When selecting additional modules and accessories, remember that an MMC adds no I/O channels, connections or supply capacity.
Navigation: Siemens automation > Siemens S7 PLC > SIMATIC S7 > Siemens ET 200