• Gemo DZ900

Gemo DZ900 is a microprocessor-based digital timer relay with simple two-button adjustment. It can operate in either ON Delay or Flasher mode, depending on the selected configuration. OtomasyonAVM has supplied Gemo products since 2013.

Standard supply voltage: 100–240 VAC, 50–60 Hz.
A 24 V supply version can be supplied when specified at the time of order.
Output: Relay output as standard. An SSR output version should be specified when ordering.

The DZ900 starts timing when supply power is applied. Applications requiring a separate START input should use the DZ482 model.

Setting the timer

The display alternates between SEt and the programmed time value. In Flasher mode, St.A is shown first, followed by St.B.

Use the Up and Down Arrow keys to change the SET value. After the required value has been entered, leave the keys untouched for approximately two seconds. The new setting is then stored automatically and the display returns to the countdown screen.

When power is applied again, the timer counts down from the stored SET value to zero and activates the output when the programmed time has elapsed.

out = dLY selects ON Delay operation. In this mode, only one SET value is required.
out = FLS selects Flasher operation. In this mode, St.A and St.B are programmed separately.

To enter the operating-mode and time-range settings, hold the Up and Down Arrow keys while switching the unit on. Release both keys as soon as the LED display lights up.

The selected maximum range and time unit are shown alternately on the display. Use the Up and Down Arrow keys to select the required range. After making the selection, leave the keys untouched for approximately five seconds. The setting is stored automatically.

Sec: seconds
Min: minutes

Available time ranges: 99.9 seconds, 999 seconds, 99.9 minutes or 999 minutes.

Gemo DZ900 main features

Operating principle: Timing starts when supply power is applied. Instantaneous contact, delayed output and Flasher operation can be selected.
Display: 3-digit, 7-segment LED display.
Displayed value: The programmed SET value or remaining time can be monitored during operation.
Memory: Program and control parameters are retained in non-volatile memory.
Connection: Plug-in terminal construction simplifies wiring, installation and replacement.

Dimensions: 96 × 96 mm
Panel cut-out: 91 × 91 mm
Supply voltage: 100–240 VAC, 50–60 Hz
Power consumption: < 6 VA

Delayed output – OUT1: Relay, NO + NC, 250 VAC / 2 A resistive load.
Instantaneous output – OUT2: Relay, NO + NC, 250 VAC / 2 A resistive load.

Resolution: 0.1 s / 1 s / 0.1 min / 1 min.
Accuracy: ±1.5% of full scale.

Operating altitude: < 2000 m.
Relative humidity: Up to 80% at 30 °C, decreasing linearly to 50% at 50 °C, non-condensing.
Protection rating: IP20 according to EN 60529.

EMC: EN 61000-6-1 and EN 61000-6-3.
Safety: EN 61010-1; pollution degree 1, measurement category I.

The DZ900, DZ721 and DZ481 models begin timing when supply power is applied. The DZ482 uses a separate START input. When replacing an existing timer, the operating method should therefore be checked in addition to the front-panel dimensions.

Models in the series:
DZ900: 96 × 96 mm
DZ721: 72 × 72 mm
DZ481 / DZ482: 48 × 48 mm

DZ482 START input: Terminals 11 and 12.

Gemo DZ900 / DZ721 / DZ481 / DZ482 User Manual (PDF)

Gemo price list
Gemo contact information
Gemo product range
Industrial control devices

Installation notice: Installation, wiring and commissioning must be carried out by qualified technical personnel.

Before installation, always check the supply voltage, terminal connections, output rating and operating mode against the product documentation. The equipment must be installed in accordance with applicable electrical, machinery and local safety regulations.

Incorrect wiring, unsuitable supply voltage or installation outside the manufacturer's specified operating conditions may damage the equipment and may invalidate warranty coverage.

For product selection, technical information or ordering assistance, please use the Gemo contact page.

Write a review

Note: HTML is not translated!
Bad Good

Gemo DZ900

  • 10.00USD

  • Ex Tax: 10.00USD

Related Products

DEZ-44-R-A -Easy timer

DEZ-44-R-A -Easy timer

The DERELL DEZ-44-R-A digital time relay is a compact and practical solution for timing operations i..

59.00USD Ex Tax: 59.00USD

DEZ-44-RS-A - With start timer

DEZ-44-RS-A - With start timer

Start input supported DERELL DEZ-44-RS-A model time relays belong to the basic time relay series com..

60.00USD Ex Tax: 60.00USD

DEZ-77-R-A - Easy timer relay

DEZ-77-R-A - Easy timer relay

The Derell DEZ-77-R-A model is part of the basic time relay family, commonly used in industrial mach..

61.00USD Ex Tax: 61.00USD

DEZ-99-R-A - Simple - Economic timer

DEZ-99-R-A - Simple - Economic timer

Derell DEZ 44 R A model time relays are devices belonging to the simple time relay series, which are..

62.00USD Ex Tax: 62.00USD