Gemo DZ307 is a programmable digital timer with separate START, RESET and GATE inputs. It is designed for applications where a simple ON-delay timer is not enough and several different timing sequences may be required. OtomasyonAVM has been supplying Gemo products since 2013.
Supply voltage: 100–240 VAC, 50–60 Hz.
A 24 VAC/DC version is available as an option.
Output: Relay output as standard. An open-collector NPN output is used on the SSR version.
START / RESET / GATE inputs: Maximum 32 VDC. OFF level: 0–2 VDC. ON level: 7–32 VDC.
The GATE input is useful when the timing process needs to be paused without losing the current time value. While GATE is active, timing stops and resumes when the input is released.
Timing functions
The DZ307 offers 13 selectable output functions. The behaviour of the START and RESET inputs changes according to the selected function.
Delayed output with START held ON: When START is ON, the timer begins counting. OUT switches ON after the t.SEt time has elapsed. OUT switches OFF when START goes OFF or RESET is activated.
Retriggerable pulse: A change at the START input, either OFF → ON or ON → OFF, switches OUT ON. OUT switches OFF after t.SEt. A new START trigger can restart the timing period while the output is still active.
Delayed output with reset requirement: Following an OFF → ON transition at START, OUT switches ON after t.SEt. A new START trigger is ignored until the timer has been reset.
START-controlled Flasher: While START remains ON, OUT stays ON for t.On, then OFF for t.OFF. This cycle repeats until START is removed or RESET is activated.
Rising-edge timed output: An OFF → ON transition at START switches OUT ON. The output switches OFF after t.SEt. Depending on the selected function, the timing period may be retriggered while OUT is active.
Triggered Flasher: An OFF → ON transition at START begins a repeating cycle. OUT remains ON for t.On and OFF for t.OFF.
Non-retriggerable pulse: START switches OUT ON and the output remains active for t.SEt. Additional START signals are ignored until the timing period has finished.
Falling-edge two-stage timing: After an ON → OFF transition at START, the timer waits for tA, switches OUT ON, then switches it OFF after tB. A new START trigger is not accepted before tB has finished.
Power-on delay: OUT switches ON after t.SEt following power-up. The START input is not used in this function. RESET switches the output OFF.
START-controlled count-up: While START is ON, OUT is active and the timer counts upward. When START goes OFF, counting stops and the displayed value is held.
Delayed OFF after falling edge: OUT remains ON while START is active. Following an ON → OFF transition, OUT switches OFF after t.SEt.
Falling-edge timed output: An ON → OFF transition switches OUT ON. OUT switches OFF after t.SEt. Returning START to ON also switches the output OFF.
Count-up with threshold output: The timer counts upward while START is ON. Counting pauses when START goes OFF. Once the accumulated value exceeds t.SEt, OUT switches ON. RESET clears the display and switches the output OFF.
RESET: RESET is used to cancel the active output and reset the timing sequence.
GATE: Timing pauses while GATE is ON. The current time value is retained.
Time ranges
99:59 hours
99:59 minutes
599.9 seconds
Resolution: 1 minute / 1 second / 0.1 second.
Accuracy: ±0.5% of full scale.
For functions using t.On and t.OFF, the minimum accepted values are 000.1 seconds, 00.01 minutes or 00.01 hours. Some functions count upward, while the remaining functions count down.
Technical details
Front dimensions: 96 × 96 mm
Panel cut-out: 92 × 92 mm
Display: Dual 4-digit, 7-segment display.
Control inputs: START / RESET / GATE.
Maximum input voltage: 32 VDC.
OFF level: 0–2 VDC.
ON level: 7–32 VDC.
Sensor supply: 12 VDC, maximum 50 mA, unregulated.
Relay output: NO – Common – NC, 250 VAC / 2 A resistive load.
SSR output: Open-collector NPN, maximum 30 V / 100 mA.
Selectable functions: 13.
Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC.
Power consumption: < 6 VA.
Relative humidity: Up to 80% at 30 °C, decreasing linearly to 50% at 50 °C, non-condensing.
Operating altitude: < 2000 m.
This type of timer is useful when timing needs to follow the machine sequence rather than simply starting whenever power is applied. The separate START, RESET and GATE inputs provide considerably more control than a basic timer relay.
Gemo price list
Gemo contact information
Gemo products
Installation: Wiring and commissioning should be carried out by qualified technical personnel.
Before powering the timer, check the supply voltage, input signal levels and relay or NPN output connections against the machine wiring diagram and the product documentation.
Incorrect wiring or operation outside the specified electrical limits may damage the timer and may affect warranty coverage.
Gemo DZ309
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DZ309-230VAC-R
- Availability: 15
-
29.00USD
- Ex Tax: 29.00USD
Related Products
DEZ-44-R-A -Easy timer
The DERELL DEZ-44-R-A digital time relay is a compact and practical solution for timing operations i..
59.00USD Ex Tax: 59.00USD
DEZ-44-RS-A - With start timer
Start input supported DERELL DEZ-44-RS-A model time relays belong to the basic time relay series com..
60.00USD Ex Tax: 60.00USD
DEZ-77-R-A - Easy timer relay
The Derell DEZ-77-R-A model is part of the basic time relay family, commonly used in industrial mach..
61.00USD Ex Tax: 61.00USD
DEZ-99-R-A - Simple - Economic timer
Derell DEZ 44 R A model time relays are devices belonging to the simple time relay series, which are..
62.00USD Ex Tax: 62.00USD




