Gemo DS204 is a programmable up/down digital counter with two counting inputs, a single preset value and one output. Several input and output modes can be selected to suit different counting applications. OtomasyonAVM has been supplying Gemo control products since 2013.
DS204 output behaviour
One of the most important points when setting up the DS204 is deciding what the OUT output should do when the preset count is reached.
Depending on the selected output mode, the counter can continue counting after reaching the preset value, hold the displayed value until RESET is applied, generate a timed pulse, or reset the count automatically.
Typical output modes include:
After counting is completed, the displayed value can continue increasing or decreasing until a RESET signal is received. If OUT is not configured as a single pulse, the output remains ON.
In another mode, the displayed count remains fixed after the preset value is reached and OUT stays ON until RESET is applied.
When a single-pulse output is selected, the display can remain fixed for the programmed pulse duration. At the end of the pulse, the output and/or count value is reset according to the selected output function.
Preset-controlled output
OUT can be configured to switch ON when the count value becomes equal to the Preset value.
If the count passes through the Preset value very quickly, a mechanical relay may not have enough time to operate. In this type of application, an SSR output may be more suitable because of its faster switching response.
OUT can also be configured to remain ON when the count value is equal to or greater than the Preset value. Where the opposite logic is required, the normally closed relay contact can be used.
Main DS204 features
Counting inputs: 2 inputs, maximum 7500 Hz, 5–30 V.
Display: Two 4-digit displays.
Counting direction: Up/down counting.
Preset: Single SET value.
Output: Single OUT output.
Parameter protection: Password-protected settings.
Selectable counting frequencies: 20 Hz, 500 Hz, 2500 Hz or 7500 Hz.
Calibration multiplier: Adjustable from 0.001 to 9.999.
OFFSET: An offset value can be added to the count.
Input / output functions: 7 selectable input modes and 9 selectable output modes.
Sensor and encoder inputs
The DS204 can be used with PNP or NPN proximity sensors and encoders with NPN, PNP or Totem-pole outputs.
NPN selection: When the “npn select” input is connected to the “+12 V” terminal, the CP1 and CP2 counting inputs operate as NPN inputs.
RESET input: Minimum 10 ms, 5–30 V positive input. For related sensor types, see our inductive sensor section.
Sensor supply output: 12 VDC, maximum 50 mA, unregulated.
OUT pulse duration
The OUT contact can operate continuously or as a timed pulse from 0.1 to 999.9 seconds.
For high-speed counting: If the Preset value is present only for a very short time, an SSR output may be more suitable than a mechanical relay.
Count memory after power loss
The DS204 can be configured to retain the last count value when power is removed. When power is restored, the stored count can be loaded again.
Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC.
If the 24 VAC/DC version is required, this must be specified when ordering.
Panel installation and electrical interference
The DS204 can be used in industrial control panels where motor drives, inverters or other possible sources of electrical interference are present. In these installations, proper separation of power and signal wiring should be observed.
For high-frequency counting inputs, keeping sensor and encoder cables away from motor and power wiring helps reduce unwanted interference.
Gemo main page
Gemo contact information
Installation: Wiring and commissioning should be carried out by qualified technical personnel.
Before powering the counter, check the supply voltage, input type, sensor polarity, counting frequency and output configuration against the product documentation.
Gemo DS204 Counter
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DS204-230VAC-R
- Availability: 12
-
36.00USD
- Ex Tax: 36.00USD
Related Products
DGC-44-RS-A - Digital Counter
The DERELL Counter is a next-generation industrial counter that features a 48x48 mm size with two ro..
40.00USD Ex Tax: 40.00USD
DGC-44-RS-B
The DERELL Counter is a next-generation industrial counter that features a 48x48 mm size with two r..
40.00USD Ex Tax: 40.00USD
DGC-446-RS-A Counter
"This product is currently unavailable for sale as a software update has been performed."The DERELL ..
41.00USD Ex Tax: 41.00USD
DGC-776-RS-A Digital counter
New generation 6-digit industrial counter :The new generation industrial counter is a device with a ..
45.00USD Ex Tax: 45.00USD




