Gemo DZ721 is a microprocessor-based digital timer relay with simple two-button adjustment. Timing starts when supply power is applied, and the unit can operate in either ON Delay or Flasher mode. OtomasyonAVM has supplied Gemo products since 2013.
Standard supply voltage: 100–240 VAC, 50–60 Hz.
A 24 V supply version can be supplied when specified at the time of order.
Output: Relay output as standard. An SSR output version should be specified when ordering.
The DZ721 starts timing when supply voltage is applied. Applications requiring a separate START input should use the DZ482 model.
Setting the time value
The display alternates between SEt and the programmed time value. In Flasher mode, St.A is displayed first, followed by St.B.
Use the Up and Down Arrow keys to change the SET value. After the required value has been entered, leave the keys untouched for approximately two seconds. The new setting is stored automatically and the display returns to the countdown screen.
When power is applied again, the timer counts down from the stored SET value to zero and activates the output when the programmed time has elapsed.
out = dLY selects ON Delay operation. Only one SET value is required in this mode.
out = FLS selects Flasher operation. In this mode, St.A and St.B are programmed separately.
To enter the operating-mode and time-range settings, hold the Up and Down Arrow keys while switching the unit on. Release both keys as soon as the LED display lights up.
The maximum time range and time unit are shown alternately on the display. Use the Up and Down Arrow keys to select the required range. After making the selection, leave the keys untouched for approximately five seconds. The selected value is then stored automatically.
Sec: seconds
Min: minutes
Available time ranges: 99.9 seconds, 999 seconds, 99.9 minutes or 999 minutes.
Gemo DZ721 main features
Operating principle: Timing starts when supply power is applied. Instantaneous contact, delayed output and Flasher operation can be selected.
Display: 3-digit, 7-segment LED display.
Displayed value: The programmed SET value or remaining time can be monitored during operation.
Memory: Program and control parameters are retained in non-volatile memory.
Connection: Plug-in terminal construction makes installation, wiring and replacement easier.
Dimensions: 72 × 72 mm
Panel cut-out: 70 × 70 mm
Supply voltage: 100–240 VAC, 50–60 Hz
Power consumption: < 6 VA
Delayed output – OUT1: Relay, NO + NC, 250 VAC / 2 A resistive load.
Instantaneous output – OUT2: Relay, NO + NC, 250 VAC / 2 A resistive load.
Resolution: 0.1 s / 1 s / 0.1 min / 1 min.
Accuracy: ±1.5% of full scale.
Operating altitude: < 2000 m.
Relative humidity: Up to 80% at 30 °C, decreasing linearly to 50% at 50 °C, non-condensing.
Protection rating: IP20 according to EN 60529.
EMC: EN 61000-6-1 and EN 61000-6-3.
Safety: EN 61010-1; pollution degree 1, measurement category I.
The DZ900, DZ721 and DZ481 models begin timing when supply power is applied. The DZ482 uses a separate START input. When replacing an existing timer, both the front-panel size and the operating method should therefore be checked.
Models in the series:
DZ900: 96 × 96 mm
DZ721: 72 × 72 mm
DZ481 / DZ482: 48 × 48 mm
Gemo price list
Gemo contact information
Gemo product range
Industrial control devices
Installation notice: Installation, wiring and commissioning must be carried out by qualified technical personnel.
Before installation, always check the supply voltage, terminal connections, output rating and selected operating mode against the product documentation. Installation must comply with applicable electrical and machinery safety requirements.
Incorrect wiring, unsuitable supply voltage or operation outside the manufacturer's specified conditions may damage the equipment and may invalidate warranty coverage.
For product selection, technical information or ordering assistance, please use the Gemo contact page.
Gemo DZ721
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DZ721-230VAC-R
- Availability: 18
-
12.00USD
- Ex Tax: 12.00USD
Related Products
DEZ-44-R-A -Easy timer
The DERELL DEZ-44-R-A digital time relay is a compact and practical solution for timing operations i..
59.00USD Ex Tax: 59.00USD
DEZ-44-RS-A - With start timer
Start input supported DERELL DEZ-44-RS-A model time relays belong to the basic time relay series com..
60.00USD Ex Tax: 60.00USD
DEZ-77-R-A - Easy timer relay
The Derell DEZ-77-R-A model is part of the basic time relay family, commonly used in industrial mach..
61.00USD Ex Tax: 61.00USD
DEZ-99-R-A - Simple - Economic timer
Derell DEZ 44 R A model time relays are devices belonging to the simple time relay series, which are..
62.00USD Ex Tax: 62.00USD




