• Gemo DS217A Counter

Gemo DS217A is a programmable up/down digital counter with two preset values and two independent outputs. Preset1 and Preset2 can be monitored on the display, and RESET can also be performed from the front panel. OtomasyonAVM has been supplying Gemo control products since 2013.

Main DS217A features

Display: Dual 4-digit, 7-segment display.
Front size: 72 × 72 mm.
Counting inputs: 2 inputs, maximum 7500 Hz, 5–30 V.
Preset values: Preset1 and Preset2.
Outputs: OUT1 and OUT2.
Connection: Plug-in terminal construction for easier wiring and replacement.

Counting frequency: 20 Hz, 500 Hz, 2500 Hz or 7500 Hz selectable.
Input / output functions: 7 selectable input modes and 10 selectable output modes.
OFFSET: An offset value can be added to the count.
Decimal point: Adjustable between the 1st and 3rd digit.
Preset1: Absolute or relative operation can be selected.

Sensor and encoder inputs

The DS217A can be used with PNP or NPN proximity sensors and encoders with NPN, PNP or Totem-pole outputs.

NPN selection: When the “npn select” input is connected to the “+12 V” terminal, CP1 and CP2 operate as NPN counting inputs.

The RESET input is always PNP. When a PNP or Totem-pole sensor is used, the “npn select” terminal is left unconnected.

RESET input: Minimum 10 ms, positive PNP input, 5–30 V.

Other compatible sensing devices can be found in our industrial sensors section.

Output configuration

OUT1 / OUT2 relay outputs: 2 × relay, Common – NO – NC, 250 VAC / 2 A resistive load.
Electronic outputs: 2 × open-collector NPN, maximum 30 V / 100 mA.

Output duration: Continuous output or a single pulse adjustable from 0.1 to 999.9 seconds.

How OUT1 and OUT2 behave

The DS217A provides several output modes, so the behaviour of OUT1, OUT2 and the displayed count after reaching a preset depends on the selected function.

After counting is completed, the displayed value can continue increasing or decreasing until RESET is applied. If OUT1 and OUT2 are not configured as single-pulse outputs, they can remain ON.

In another mode, OUT1 switches OFF at the end of the OUT2 pulse period while counting continues. The OUT1 pulse timing operates independently from OUT2.

The counter can also be configured so that OUT1 and the count value are reset when the OUT2 pulse period ends.

Another option holds the displayed count at the final value during the OUT2 pulse period. When the pulse ends, OUT1 and the count value are reset.

It is also possible to reset the internal count immediately while keeping the final value on the display until the OUT2 pulse period has finished.

Preset1 and Preset2 operation

OUT1 can switch ON when the count reaches Preset1, while OUT2 can switch ON when the count reaches Preset2.

If the count passes through Preset1 or Preset2 very quickly, a mechanical relay may not have enough time to operate. In high-speed applications, an SSR or electronic output may be more suitable because of its faster switching response.

For high-speed counting: If Preset1 or Preset2 is present only for a very short time, the response time of the mechanical relay should be taken into account.

Depending on the selected function, OUT1 can also be active when the count is equal to or below Preset1, while OUT2 can be active when the count is equal to or above Preset2.

Count memory after power loss

The DS217A can retain the last count value when power is removed. When power is restored, the stored value can be loaded again.

Program and control parameters are also retained in memory.

Supply voltage: Standard supply depends on the ordered version. A 24 VAC/DC supply version is available.

If the 24 VAC/DC version is required, this must be specified when ordering.

Panel installation

When the DS217A is installed in a panel containing motor drives or inverters, sensor and encoder wiring should be kept away from motor and power cables where possible.

This is especially important at higher counting frequencies, where electrical interference can cause incorrect counts or unstable input signals.

Gemo DS217A User Manual (PDF)

Gemo main page
Industrial control devices

Write a review

Note: HTML is not translated!
Bad Good

Gemo DS217A Counter

  • 40.00USD

  • Ex Tax: 40.00USD

Related Products

DGC-77-RS-A

DGC-77-RS-A

DERELL DGC-77-RS-A is an industrial counter. It counts pulses or switching events for monitoring and..

42.00USD Ex Tax: 42.00USD

DGC-77-RS-B

DGC-77-RS-B

DERELL DGC-77-RS-B is an industrial counter. It counts pulses or switching events for monitoring and..

43.00USD Ex Tax: 43.00USD

DGC-776-RS-A Digital counter

DGC-776-RS-A Digital counter

New generation 6-digit industrial counter :The new generation industrial counter is a device with a ..

45.00USD Ex Tax: 45.00USD

DGC-776-RS-B

DGC-776-RS-B

DERELL DGC-776-RS-B is an industrial counter. It counts pulses or switching events for monitoring an..

46.00USD Ex Tax: 46.00USD