Gemo DS207 is a programmable up/down digital counter with two counting inputs, one preset value and a single output. It supports several input and output modes for different counting applications. OtomasyonAVM has been supplying Gemo control products since 2013.
DS207 output behaviour
One of the main points when setting up the DS207 is deciding what should happen when the counter reaches the Preset value.
Depending on the selected output function, the displayed count value may continue increasing or decreasing until RESET is applied, remain fixed after the preset is reached, or reset automatically after the output pulse has finished.
If OUT is not configured as a single pulse, the output can remain ON until a RESET signal is received.
With a timed pulse selected, the display can remain fixed during the programmed OUT pulse period. At the end of the pulse, the count value and output are reset according to the selected output mode.
Preset-controlled output
OUT can switch ON when the count value becomes equal to the Preset value.
If the counter passes through the Preset value very quickly, a mechanical relay may not have enough time to operate. In this situation, an SSR output may be more suitable because of its faster switching response.
OUT can also be configured to remain ON while the count is equal to or greater than the Preset value. Where the opposite logic is required, the normally closed relay contact can be used.
For high-speed counting: If the Preset value is present only for a very short time, an SSR output may be preferable to a mechanical relay.
Main technical features
Counting inputs: 2 inputs, maximum 7500 Hz, 5–30 V.
Display: 2 × 4 digits.
Counting direction: Up/down counting with selectable input behaviour.
Preset: Single SET value.
Output: Single OUT output.
Parameter protection: Password-protected settings.
Selectable functions: 7 input modes and 9 output modes.
OFFSET: An offset value can be added to the count.
Counting frequencies: 20 Hz, 500 Hz, 2500 Hz or 7500 Hz.
Calibration multiplier: Adjustable from 0.001 to 9.999.
Sensor and encoder inputs
The DS207 can be used with PNP or NPN proximity sensors and encoders with NPN, PNP or Totem-pole outputs.
NPN selection: When the “npn select” input is connected to the “+12 V” terminal, CP1 and CP2 operate as NPN inputs.
RESET input: Minimum 10 ms, positive PNP input, 5–30 V.
Sensor supply output: 12 VDC, maximum 50 mA, unregulated.
OUT pulse duration
The OUT contact can operate continuously or as a timed pulse adjustable from 0.1 to 999.9 seconds.
Count memory after power loss
The DS207 can retain the last count value when power is removed. When power is restored, the stored value can be loaded again.
Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC supply.
If the 24 VAC/DC version is required, this must be specified when ordering.
EMC and panel installation
The DS207 can be used in industrial control panels where motor drives and inverters or other possible sources of electrical interference are present. Signal and power wiring should be separated where possible, especially when the counter is used at higher input frequencies.
Keeping sensor and encoder cables away from motor and power wiring helps reduce unwanted interference in high-speed counting applications.
Gemo main page
Industrial sensors
Industrial control devices
Gemo DS207 Counter
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DS207-230VAC-R
- Availability: 12
-
40.00USD
- Ex Tax: 40.00USD
Related Products
DGC-44-RS-A - Digital Counter
The DERELL Counter is a next-generation industrial counter that features a 48x48 mm size with two ro..
40.00USD Ex Tax: 40.00USD
DGC-44-RS-B
The DERELL Counter is a next-generation industrial counter that features a 48x48 mm size with two r..
40.00USD Ex Tax: 40.00USD
DGC-446-RS-A Counter
"This product is currently unavailable for sale as a software update has been performed."The DERELL ..
41.00USD Ex Tax: 41.00USD
DGC-776-RS-A Digital counter
New generation 6-digit industrial counter :The new generation industrial counter is a device with a ..
45.00USD Ex Tax: 45.00USD




