Delta HMI Printer Expansion Modules

Delta HMI printer expansion modules add a printer interface to compatible legacy operator panels. The ordering code confirmed by the manufacturer’s English catalogue and software manual is DOP-EXPM110. The module supports sending screen or project-formatted output to a printer; that printer must also be supported by the HMI software.

DOP-EXPM110 parallel printer interface

DOP-EXPM110 provides a 25-pin parallel printer port. The catalogue specifies DC 5 V, 1 A, supplied by the HMI. This is not the printer’s mains rating; do not apply an arbitrary external 24 V supply to the module. The listed operating environment is 0–50 °C and 10–90% relative humidity.

The catalogue footnote limits this expansion to the DOP-AE family. A shared manual cover mentioning DOP-A or DOP-AS does not establish the same expansion slot on every model. The manufacturer’s May 2008 news also lists DOP-EXPM110 among DOP-AE expansion modules.

Check the exact panel code, rear expansion interface, module label, fixing points and connector clearance together. Similar appearance does not establish DOP-B or DOP-100 compatibility. Back up the existing HMI project, then remove power before installing or connecting the module.

How to interpret the DOP-EXM110 spelling

DOP-EXM110 appears beside the printer-module drawing on PDF page 8 of the Russian HQ05 DOP-A/AE/AS instruction dated 20 August 2007. The English catalogue and ScrEdit manual use DOP-EXPM110. This documentation difference does not prove two distinct hardware variants or an official model-code change.

For ordering, replacement or used equipment, rely on the complete model label on the part and the matching manufacturer document. An old “EXM110” entry alone does not establish interchangeability. The 2007 and 2008 document dates also do not define the beginning or end of the product family.

Parallel printing versus USB printing

A parallel printer connection uses DOP-EXPM110. The project’s “Parallel Port” selection must match the physical printer interface and cable. A 25-pin D-sub connector does not establish an RS-232 connection.

USB printing depends on a supporting panel’s USB Host interface and printer support. A USB Client programming connection serves a different purpose. Working on a computer or fitting the connector does not by itself establish HMI printer compatibility. Do not assume a general USB-to-parallel adapter replaces this HMI expansion.

Screen Editor / ScrEdit print settings

Review printing in the Screen Editor / ScrEdit project for this hardware generation. The archived manual’s Configuration / Print section selects the printer manufacturer/model, paper, margins and Parallel Port or USB interface. It explicitly requires DOP-EXPM110 for the parallel option.

Hard Copy prints the current screen; Print Typesetting handles formatted output and history data. Start commissioning with short fixed output, then check dates, values, page breaks and required language characters. Correct display on the HMI does not prove the same printed layout.

Use the official Delta Download Center for software and document searches. Record the working project release and exact panel before changing software. Do not assume this legacy module can be configured in DOPSoft or TPEditor on every HMI.

Distinguish other HMI expansions

DOP-EXPM110 serves the printer connection. Digital I/O expansions serve field signals, while Ethernet expansions provide network connectivity. Membership in the same DOP-AE accessory group does not make their functions or connector pins identical.

Use mounting and power connections for installation and select programming and HMC cables for their actual transfer or communication task. Distinguish the panel’s 24 V supply discussed under HMI power supplies from the catalogue’s 5 V module supply.

Editor’s note

Photograph both the HMI and module labels before selecting a replacement. An old EXM110 listing does not identify an unlabelled EXPM110 part. Missing labels and swapped cases deserve particular attention on used equipment.

Print the printer’s own test page and check paper, ribbon/toner and fault indicators before changing the HMI. A printer that cannot pass its local test should be investigated independently.

Begin with a small fixed text sample, then add numbers, dates and the required character set. Garbled characters, displaced lines and no output are different symptoms; narrow the printer selection and layout checks accordingly.

Inspect bent pins, corrosion and loose connector screws. Check cable continuity with power removed and the correct drawing available. Connector pin count alone is not a cable specification.

For panel restarts during printing, inspect the supply under load and the connections. Keep the HMI-supplied module power separate from the printer’s own supply. Do not inject external voltage into unidentified connectors.

Preserve a working project before factory resets or firmware writes. After a print-setting change, recheck normal screens, alarms and communication. Save a test print and the exact printer model with the project backup.

Documents and related topics

Use the Delta HMI PDF archive to select documents. The DOP-AE catalogue establishes hardware scope, the Screen Editor manual explains printing, and the Russian HQ05 instruction records the historical EXM110 drawing label. Match the exact model and document edition before installation.

Delta HMI Communication Peripheral Units · Delta HMI Remote I/O Modules · Delta HMI Starter Kits

Delta DOP-H07 · Delta DOP-W · Delta DOP-107H

External references

Delta HM 2008 HMI bülteni / product news · Delta DOP-A/AE/AS Screen Editor manual