Delta HMI Remote I/O Modules

The HM/HMC-RIO units covered under Delta HMI remote I/O modules connect field inputs and outputs to an HMC controller. Selection goes beyond 32 inputs / 32 outputs: match the communication link, input wiring, relay/transistor outputs and exact HMC model together.

This group concerns HMC07 and HMC08 control systems. Remote I/O differs from the screen itself, local digital I/O expansion and a standalone PLC. A machine having a DOP-B or DOP-100 screen does not automatically establish support.

HM-RIO3232T12: high-speed RS-422 remote I/O

HM-RIO3232T12 is a 24 VDC RS-422 remote I/O model with 32 NPN (Sink) inputs and 32 transistor outputs. The manufacturer’s 2021 specification table limits it to HMC08-N500. Do not select it under a generic HMC-compatible description without checking the complete controller code and project generation.

Its RS-422 connection belongs to the corresponding HMC remote I/O arrangement. An RS-422 port on another device does not prove support or establish a protocol such as Modbus. Verify input commons, output groups and the communication cable against the exact model’s wiring diagram.

HM-RIO3232RT5 / HMC-RIO3232RT5: DMCNET and mixed outputs

The manufacturer’s download record uses HM-RIO3232RT5, while catalogue model rows use HMC-RIO3232RT5. The listed RT5 uses DMCNET and 24 VDC, with 32 NPN/PNP inputs and 16 relay + 16 transistor outputs. Distinguish it from the T12 high-speed RS-422 link.

Treat RT5 relay and transistor groups separately for load type and switching rate. Check commons, permitted loading and inductive-load suppression for each group. Record the HM/HMC prefix and document edition; similar names alone do not establish the hardware revision or cable interchangeability.

HMC-RIO3232T15: DMCNET and all-transistor outputs

HMC-RIO3232T15 is listed separately from RT5 in the 2021 catalogue: DMCNET, 24 VDC, 32 NPN/PNP inputs and 32 transistor outputs. It is not a drop-in replacement for RT5 where relay outputs are required. T12 and T15 are different modules.

Read the RT5/T15 catalogue phrase “For all models” within the HMC models covered by that catalogue. It does not establish compatibility with every Delta PLC or HMI. The 2019 and 2021 model lists differ; use the installed part’s complete label and matching technical document.

Electrical wiring and load selection

Distinguish the module supply from the field-load supply. Match NPN/PNP input wiring to the sensor output and the correct common arrangement. NPN/PNP support does not establish unrestricted mixed wiring on every channel without checking the diagram.

Alongside channel current, check common/group limits, simultaneous loading, load type and switching duty. A catalogue maximum frequency or per-point current does not mean every channel can operate at that value simultaneously under all conditions. Do not combine values from different editions into a new composite specification.

Size the control-system power supply for the controller, I/O and field loads. Check terminals, commons, panel grounding and cable routes under mounting and power connections. Working controller communication does not prove that every output group has its field supply.

Communication cables and commissioning

Verify the high-speed RS-422 I/O link and DMCNET network separately. A fitting connector does not establish protocol, pinout, shielding or cable-length suitability. Select programming and HMC cables by full code and endpoint function; an Ethernet expansion is not an automatic substitute.

Before replacement, record the HMC project, software/firmware release, I/O address map and any node settings. Initially observe inputs without causing load movement, then test outputs individually with a suitable test load. Establish communication-loss output behaviour from actual project settings and testing.

Use the official DOPSoft HMC manual record, HM-RIO3232T12 installation record and HM-RIO3232RT5 installation record for software and documentation selection. Check the existing HMC project’s release requirements before choosing a general PLC/HMI editor.

Editor’s note

Photograph the HMC and RIO labels and every terminal before removal. Preserve the T12, RT5 and T15 suffixes. Matching I/O counts do not establish interchangeable modules.

For a missing input, check the sensor output, common and voltage seen by the module. Compare the input LED with the addressed status in the HMC project. An illuminated LED does not prove that the project is observing the correct address.

Test RT5 relay and transistor groups separately. Do not treat a semiconductor output as a dry relay contact. If a shorted or excessive load is suspected, do not transfer it to a working channel and damage that channel too.

For communication dropouts, inspect the cable, shield connection, loose plugs and voltage dips first. Software parameters will not repair the wrong cable. Distinguish DMCNET wiring from the RS-422 I/O link before testing.

Prevent unexpected motion from motors, valves and contactors during initial tests. Observe inputs first, then test outputs with controlled loads. Include cable loss and controller restart in the recorded output-behaviour checks.

Find the original fault before installing a replacement. Examine supply, load current, coil suppression and terminal heating so the same fault is not repeated. Keep the last working project and I/O address list with the replacement record.

Documents and related topics

Use the Delta HMI PDF archive to select models and editions. A catalogue distinguishes families and I/O types; exact-model installation/operation instructions are needed for pins, channel limits and field wiring. A document date alone does not define a generation or substitution boundary.

Delta HMI Printer Expansion Modules · Delta HMI Communication Peripheral Units · Delta HMI Starter Kits

Delta TP04P · Delta TP70P

Delta DOP-H07 · Delta DOP-107H

External references

Delta HMC manufacturer catalogue — 2021-06-11 · Delta Download Center