Delta IFD9507
Delta IFD9507
Delta IFD9507 is an industrial gateway linking Ethernet-side Modbus TCP and EtherNet/IP communication with RS-232 / RS-485 serial Modbus equipment. It provides a 10/100 Mbps RJ45 Ethernet connection for network monitoring and data exchange with existing serial PLCs, operator panels or drives.
Ethernet and serial port distinction
COM1 is RS-232 through Mini-DIN; COM2 is RS-485 through RJ11. A 10-pin terminal block also provides RS-485 connections. Identify the electrical interface from the documentation and match Delta DVP communication cables to the connected device's port drawing.
The manual specifies RJ11 pin 3: D+, pin 4: D−, pin 5: GND, and RS-232 Mini-DIN pin 4: Rx, pin 5: Tx, pin 8: GND. Read these assignments using the connector orientation shown in the drawing. Viewing a plug from the rear can reverse the apparent conductor order.
Identify the connected equipment through Delta DVP PLC series and Delta HMI files. Review panel and servo connection options under Delta HMI communication peripheral units and Delta servo communication units. Do not assume that every device supports the same Modbus commands and address layout.
Power and auxiliary functions
IFD9507 requires 24 VDC with −15% / +20% tolerance and has a specified power consumption of 3 W. Its RS-485 channel is isolated. Review supply selection alongside Delta DVP power supplies and follow the hardware drawing for reference and protective earth connections.
Three digital inputs can trigger e-mail alarms. Web configuration and monitoring, a monitor table and Virtual COM are also available. Test these functions with the actual software environment, device firmware and relevant server settings.
DCISoft and operating mode
Use Delta DCISoft for configuration and review related tools under Delta PLC software. Select Serial Master / Serial Slave, the serial port, application protocol and data mapping for the same project scenario. Establishing an Ethernet connection alone does not confirm correct data acquisition from the serial device.
During commissioning, first check the IP address and subnet mask, then station address, serial speed, parity and ASCII/RTU selection. Next, test a single known register. On the EtherNet/IP side, verify the communication arrangement supported by the connected equipment as well.
Differences from other Delta interfaces
The need for EtherNet/IP is an important distinction when comparing Delta IFD9506. Delta IFD9502 serves DeviceNet, Delta IFD9503 serves CANopen, and Delta IFD6500 provides USB-to-RS-485 conversion. Delta ADP485-01 is an RS-485 connection adapter. Connector or brand similarity does not establish these models as replacements for IFD9507.
Review Delta DVP specialty communication modules when comparing an external gateway with CPU-associated communication hardware. The appropriate solution depends on the machine's existing ports and target network protocol.
Manual and connection documents
Start document selection at Delta PLC accessories files. In the IFD9507 Application Manual, printed pages 4–8 cover hardware and connections, while pages 21–37 cover DCISoft settings. These correspond to PDF pages 6–10 and 23–39 in the downloaded 72-page document.
Editor's Note
Record the settings before removing the original unit. Keep the IP address, subnet mask, operating mode, serial port and station address together. Photograph the front switches and terminal connections as well.
Check the power supply and Ethernet connection separately. Measure terminal voltage under load, then inspect the network link. An illuminated link LED does not confirm correct Modbus or EtherNet/IP exchanges.
If ping succeeds but data is missing, inspect the serial side. Check COM selection, RS-485 polarity, speed, parity and device address in order. Changing several settings at once makes the original fault harder to identify.
Begin with one known data item. Compare the software's register addressing, data length and word order. Do not perform the first connection test by sending arbitrary write commands to machine outputs.
Do not use reset as a routine troubleshooting step. Preserve the existing configuration first. When buying used, test Ethernet, RS-232 and RS-485 in the intended application; powering the unit alone is insufficient.
Related topics
Browse parent groups under Delta DVP interfaces and Delta PLC accessories, and device documents under Delta PLC and HMI manuals and Delta manuals.
External references: Delta IFD9507 manufacturer application manual — English · Delta IFD9507 official product information · Delta IFD series official function comparison.