The REP 37-S-220 is a standard series digital/electronic potentiometer with dimensions of 37 x 72mm and a power supply voltage input of 220V.
This device is a digital/electronic potentiometer that can increase or decrease the output analog value (DC 0-10 volts) through digital buttons. The output voltage value can be proportioned to the status of the machine by the multiplier value or can be set to a 1:1 ratio if desired.
This product is usually used for speed control in speed control devices. It not only sets the speed but also has parameters for the output value being on/off when energy first comes and for adjusting ramp times.
Low and high speed levels can be set by determining the output voltage limits through the device.
In the event of a power outage, the device can continue from the last point it stopped by saving it in its memory or can be started with a ramp from zero, as desired.
The energy supply voltage of the device can vary by model. Products sold domestically are manufactured as 12VDC, 24VDC, and 220VAC.
The REP electronic potentiometer and analog control device are designed for industrial machine environments. It has galvanized insulation and can work side by side with other products that emit potential interference, such as power supplies, frequency inverters, servo drivers, etc.
Specifications include:
Power supply: 230VAC (+10%~-20%) 50/60Hz, 24VOLT DC, 12 VOLT DC
Box size: 35mm x 77mm x 75mm and 72mm x 72mm x 75mm
Display: 1 x 3-digit 14mm LED display, 4-digit in 72 x 72 models
Keypad: 4 micro switches
Operating temperature: 0 ~ 50 oC
Output voltage: 0 ~ 10VDC (20mA max.) // For 4-20mA, see the "P" model
Scale range: -199 ~ 800
Maximum output current: 10mA
Output voltage resolution: 1/10,000
Protection (keypad part): IP65
Operating humidity: 10% - 90% (without condensation)
External digital input for speed adjustment: None (see the REP series "S" model for this feature)
Relay outputs: None (see the REP series "P" model for this feature)
Note that this device cannot be used as an adjustable power supply. Its production purpose is solely for adjusting reference in speed control devices, so do not connect any other receiver or load to its output.
Editor's note: The REP series has been discontinued and replaced by the DPT series potentiometers. The REP series was a problematic product due to the keypad's usability issues, well-known problems on the case, and low resolution. However, all of these problems have been solved in the new series with an additional new processor, higher resolution, and it is recommended to choose the new series. (Personal opinion)
However, this series is only recommended for backup purposes as it is an old model. Below, similar products are recommended for new projects.
This device is a digital/electronic potentiometer that can increase or decrease the output analog value (DC 0-10 volts) through digital buttons. The output voltage value can be proportioned to the status of the machine by the multiplier value or can be set to a 1:1 ratio if desired.
This product is usually used for speed control in speed control devices. It not only sets the speed but also has parameters for the output value being on/off when energy first comes and for adjusting ramp times.
Low and high speed levels can be set by determining the output voltage limits through the device.
In the event of a power outage, the device can continue from the last point it stopped by saving it in its memory or can be started with a ramp from zero, as desired.
The energy supply voltage of the device can vary by model. Products sold domestically are manufactured as 12VDC, 24VDC, and 220VAC.
The REP electronic potentiometer and analog control device are designed for industrial machine environments. It has galvanized insulation and can work side by side with other products that emit potential interference, such as power supplies, frequency inverters, servo drivers, etc.
Specifications include:
Power supply: 230VAC (+10%~-20%) 50/60Hz, 24VOLT DC, 12 VOLT DC
Box size: 35mm x 77mm x 75mm and 72mm x 72mm x 75mm
Display: 1 x 3-digit 14mm LED display, 4-digit in 72 x 72 models
Keypad: 4 micro switches
Operating temperature: 0 ~ 50 oC
Output voltage: 0 ~ 10VDC (20mA max.) // For 4-20mA, see the "P" model
Scale range: -199 ~ 800
Maximum output current: 10mA
Output voltage resolution: 1/10,000
Protection (keypad part): IP65
Operating humidity: 10% - 90% (without condensation)
External digital input for speed adjustment: None (see the REP series "S" model for this feature)
Relay outputs: None (see the REP series "P" model for this feature)
Note that this device cannot be used as an adjustable power supply. Its production purpose is solely for adjusting reference in speed control devices, so do not connect any other receiver or load to its output.
Editor's note: The REP series has been discontinued and replaced by the DPT series potentiometers. The REP series was a problematic product due to the keypad's usability issues, well-known problems on the case, and low resolution. However, all of these problems have been solved in the new series with an additional new processor, higher resolution, and it is recommended to choose the new series. (Personal opinion)
REP-37-S-220 Digital potentiometer
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands DERELL
- Product Code: REP-37-S-220
- Availability: 9
-
300.00USD
- Ex Tax: 300.00USD
Related Products
DTP-37A electronic potentiometer
The DTP-37A is an electronic potentiometer that has a 220-volt power supply and a size of 37x72 mm. ..
255.00USD Ex Tax: 255.00USD