Gemo DTH7-230VAC Economic Auto-tune PID Temperature Controller
Gemo control products have been sold by our company since 2013.
Gemo DTH7 is a 72x72 mm economic-series Auto-tune PID temperature controller for heating applications. Relay and SSR control outputs are built into the controller and the required output mode is selected from the parameter menu.
Front size: 72x72 mm
Panel cut-out: 68x68 mm
Supply: 100..240VAC, 50-60Hz
24V version: 20..32VDC / 14..28VAC
Power consumption: < 8VA
DTH7 Main Features
Although DTH7 belongs to the economic series, it includes Auto-tune PID control, a minimum 1 second control period, ramp / soft-start, selectable 0.1 °C resolution and adjustable overshoot reduction.
DTH7 is a heating-only controller and does not have a separate alarm output.
Relay and SSR Outputs
Both relay and SSR control outputs are available on the DTH7. Output operation is selected from the controller menu:
rLY: Relay output only
SSr: SSR output only
r-S: Relay and SSR outputs active together
Relay output: 250VAC, 2A resistive load
SSR output: 12VDC, 20mA
For high-cycle heater switching, an external SSR relay can be used. Standard switching components are available in our relay and socket section.
Sensor Inputs
DTH7 is a multi-input controller supporting J, K, T, S and R type thermocouples and Pt100.
J type T/C: -100 .. 600 °C
J type T/C (J.0): -100.0 .. 600.0 °C
K type T/C: -100 .. 1300 °C
K type T/C (K.0): -100.0 .. 999.9 °C
T type T/C: -100 .. 400 °C
T type T/C (T.0): -100.0 .. 400.0 °C
S type T/C: 0 .. 1750 °C
R type T/C: 0 .. 1750 °C
Pt100: -100 .. 600 °C
Pt100 (Pt.0): -100.0 .. 600.0 °C
Resolution: 1 °C or 0.1 °C
Accuracy: ±1% of full scale
Thermocouple inputs use cold-junction compensation. Pt100 input supports up to 10 Ohm line compensation with a 3-wire connection.
When a 2-wire Pt100 is used, terminals 13 and 14 must be bridged.
Auto-tune PID Control
Control mode can be selected as ON-OFF, P, PI, PD or PID control.
The built-in Auto-tune function calculates PID parameters for the connected heating process.
Proportional band (Pb.C): 5 .. 150 °C
Integral time (Ti): 0:00 .. 30:00 min:sec
Derivative time (Td): 0:00 .. 10:00 min:sec
Control period (Ct): 1 .. 200 sec
If Ti is set to 0, the integral section is disabled and control operates as P or PD. If Td is set to 0, the derivative section is disabled and control operates as P or PI.
Heating hysteresis (H.Hys): 0 .. 50 °C or 0.0 .. 50.0 °C with decimal inputs. When H.Hys is set to 0, PID control is active.
Offset: -100 .. +100 °C or -100.0 .. +100.0 °C with decimal inputs.
Ramp / Soft-start
Ramp rate (C-t): 0.0 .. 300.0 °C/min.
When C-t is set above 0, the working SET value rises gradually at the selected rate after power-up instead of applying the final temperature demand immediately.
This function is useful for hot-runner systems, mould heating and other applications where a controlled warm-up is required.
Overshoot Adjustment
The o.Sht parameter is used to reduce temperature overshoot in PID operation. Available settings are OFF, 10.0, 5.0, 3.0, 1.0 and 0.2.
The overshoot setting should be selected according to the thermal response of the process.
Sensor Failure
If the sensor or sensor cable is open, the measurement is outside the available range or the input cannot be measured, the controller enters FAIL mode.
During a sensor failure, the OUT duty cycle can be set from 0 to 100% with the P.Err parameter.
P.Err = 0: OUT remains OFF
P.Err = 100: OUT remains continuously ON
Intermediate values: OUT remains ON for the selected percentage of the Ct period
Display and Memory
Display: 4-digit PV + 4-digit SV, 7 segment
SET display: ON / OFF selectable
Parameter memory: EEPROM
Password protection: Yes
Program and control parameters are retained when the power is switched off.
Other Specifications
Protection: IP20
Operating temperature: 0 .. 50 °C
Storage temperature: -10 .. 60 °C
Humidity: < 70%, non-condensing
Operating altitude: < 2000 m
Weight: < 0.5 kg
DTH7 Versions
DTH7-230VAC: 100..240VAC, 50-60Hz
DTH7-24V: 20..32VDC / 14..28VAC
Both versions include relay and SSR control outputs. The required output mode is selected from the controller parameters.
Gemo DTH7 User Manual (PDF)
Installation
DTH7 is intended for fixed panel mounting. Installation and wiring must be carried out by qualified technical personnel with all power sources disconnected.
External fuses must be selected according to the supply and load circuits specified in the Gemo user manual.
Gemo DTH7
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DTH7-230VAC-R
- Availability: 12
-
34.00USD
- Ex Tax: 34.00USD
Related Products
DESA-77R-A Analog Temperature Controller, 220V
▪︎ DERELL DESA-77R-A >> 220V Power Supply, Relay Output, 72x72 mm Panel Type Temperature Contr..
128.00USD Ex Tax: 128.00USD
DGS-77R-A Advanced Temperature Controller (220V)
— Next-generation temperature compensation with high precision DGS-77R-A >> 220V pow..
131.00USD Ex Tax: 131.00USD
DGS-77T-A – Advanced Serial Type with SSR Output – 220V
— Next-generation temperature compensation with high precision DGS-77T-A >> 220V pow..
136.00USD Ex Tax: 136.00USD
DGS-77R-B Advanced Temperature Controller (24VAC/DC)
— Next-generation temperature compensation with high precision DGS-77R-B >> 24VDC/AC..
205.00USD Ex Tax: 205.00USD




