What is ASI BUS (As-interface)?

AS-i AS-Interface actuator sensor industrial bus

AS-i — Actuator Sensor Interface is an industrial communication system designed primarily for connecting sensors and actuators at the lowest field level with minimal wiring. One of the defining features of AS-Interface is that communication data and device power can travel together over the same two conductors.

In simple terms: instead of wiring dozens of sensors, pushbuttons, limit switches, valves and motor starters individually back to a PLC cabinet, AS-i allows many of those field devices to connect to one simple two-conductor network.

Why was AS-Interface developed?

Traditional machine wiring can require a separate cable from every sensor and actuator back to the main control cabinet. On a long conveyor or packaging line this can create large cable bundles, many terminals, long installation times and difficult fault tracing.

AS-i was developed to simplify this sensor/actuator level. Proximity switches, photoelectric sensors, pushbuttons, valve islands, motor starters and distributed I/O modules can be connected locally along the machine.

The AS-i master or gateway then presents those field signals to the main PLC or higher-level industrial communication system.

How can AS-i carry data and power on only two wires?

The important principle is that both conductors form the AS-i communication and power circuit together. Data communication is superimposed on the DC supply carried by the same pair.

The older explanation that “one wire carries power and the other wire carries data” is incorrect. The two conductors work as a pair, simultaneously supporting communication and power distribution to suitable AS-i devices.

The well-known AS-i profile cable is usually yellow and has a mechanically keyed shape that reduces wiring errors. Many modules use piercing technology, allowing the device contacts to penetrate the cable insulation without stripping individual conductors.

Higher-power actuators can use a separate auxiliary supply where required. For example, larger solenoid loads may receive power from a separate 24 VDC circuit while communication remains on the yellow AS-i cable.

The network supply must also be designed correctly. AS-i installations can use dedicated AS-i supplies or suitable decoupling arrangements together with an industrial power supply.

Which network topologies can AS-i use?

AS-i allows considerably more topology flexibility than many traditional fieldbus systems. Line, star and tree structures can be used, and field devices can be attached where they are physically needed.

This is useful in conveyors, packaging machines and material-handling systems because remote I/O can be installed close to the actual sensors and actuators instead of routing every signal back to one central cabinet.

How long can an AS-i network be?

A standard AS-Interface segment is typically designed around a total network length of approximately 100 m. Branches and spur lengths are included in the network-length calculation.

Repeaters and suitable extension technology can increase the total network reach. Current AS-Interface documentation describes systems extending to 500 m and beyond, depending on the network architecture and components used.

For this reason, neither “AS-i is always limited to 100 m” nor “AS-i can be extended without practical limits” is technically accurate.

What is ASi-3?

ASi-3 is the established generation of AS-Interface with a very large installed base in machines, conveyors, valve systems, remote I/O and safety installations.

Classic ASi-3 communication operates at approximately 167 kbit/s. Earlier Version 2.0 systems supported up to 31 slaves, while later A/B addressing allows up to 62 slaves on compatible systems.

Typical ASi-3 cycle times are in the millisecond range. A 31-device system can be updated in approximately 5 ms, while full A/B-addressed networks can require longer overall update times depending on the master and configuration.

The older figure of 31.25 kbit/s sometimes associated with AS-i is therefore incorrect for classic AS-Interface communication.

What is ASi-5?

ASi-5 is the newer generation of AS-Interface. It keeps the low-wiring two-conductor concept but substantially increases available process data, device count and communication performance.

ASi-5 uses OFDM — Orthogonal Frequency Division Multiplexing instead of the classic pulse-modulation method.

Current ASi-5 system parameters include:

Active devices: up to 96.
Basic cycle time: approximately 1.2 ms.
Subcycle with 96 devices: approximately 5 ms.
Process data per device: up to 32 bytes input and 32 bytes output.
Total cyclic process data: up to 3072 bytes input and 3072 bytes output.

This allows AS-i to support more complex intelligent field devices in addition to traditional binary sensors and actuators.

Can older AS-i devices work with ASi-5?

Yes, with suitable ASi-5/ASi-3 master and gateway equipment. Backward compatibility is an important part of the current AS-Interface architecture.

This can allow an existing production line to retain older sensors and AS-i field modules while newer ASi-5 devices are added during machine modernization.

What does an AS-i master do?

The AS-i master manages communication on the field network, collects input/output process data and provides diagnostic information to the higher-level controller.

The master can be integrated directly into a PLC family or used as a separate gateway. For example, Siemens provides AS-i master solutions for SIMATIC PLC platforms, allowing a controller to access dozens of AS-i sensors and actuators through one field network.

What does an AS-i gateway do?

An AS-i gateway connects the lower-level actuator/sensor network to a higher-level automation network.

Depending on the product, the upper network can use PROFINET, PROFIBUS, EtherNet/IP, Modbus TCP, POWERLINK or another industrial communication technology.

This means AS-i does not have to compete with Ethernet. AS-i can handle the sensor/actuator layer while Ethernet carries controller, HMI and plant-level traffic.

How is AS-i used with industrial sensors?

AS-i was specifically designed for the sensor and actuator level.

An intelligent AS-i sensor can connect directly to the bus. Conventional NPN or PNP inductive, capacitive and photoelectric sensors can instead connect to local AS-i input modules.

A conveyor can therefore use many distributed field sensors without requiring a separate multicore cable from every sensing point back to the control cabinet.

Can an encoder use AS-i?

A conventional high-speed A/B/Z encoder should not be treated like a simple binary AS-i input. Fast pulse counting normally requires an appropriate high-speed counter or motion controller.

ASi-5 increases the amount and complexity of process data that can be exchanged with intelligent devices, but the real-time feedback requirements of an encoder used for closed-loop servo control still need to be distinguished from ordinary sensor-network traffic.

The encoder's output type — such as TTL, HTL or RS-422 — also remains a separate electrical-interface issue.

How are actuators controlled through AS-i?

Solenoid valves, motor starters, contactors and other field actuators can be controlled through AS-i output modules.

For example, an AS-i module on a conveyor can energize a motor contactor while monitoring the contactor's auxiliary feedback contact through an input on the same local station.

This is particularly useful when distributed switchgear and motor-control devices are installed far from the central PLC cabinet.

Can AS-i communicate with motor drives?

Yes, where a suitable interface is provided. Some distributed motor starters and AC drives / VFDs can exchange basic control and status information through AS-i.

This is especially useful on conveyor systems where motors and control modules are physically distributed along a production line.

AS-i should not, however, be treated as the primary high-performance synchronization network for tightly coupled multi-axis servo systems. Applications requiring fast synchronized axes normally use dedicated motion-control technologies such as EtherCAT or Sercos.

How does AS-i appear on an HMI or SCADA system?

AS-i normally operates below the operator-interface layer. The PLC gathers sensor and actuator states through the AS-i master and can then make those values available to an HMI.

The same process information can be passed to a SCADA system for alarms, production monitoring, fault history and centralized diagnostics.

An operator can therefore see an “AS-i sensor missing” or “remote module fault” alarm on the HMI even though the HMI itself does not communicate directly with every AS-i device.

Can AS-i be used in building automation?

Although AS-i is primarily associated with machines and factory field wiring, it can also be used in selected building automation applications where many distributed sensors and actuators need economical connection.

AS-i and BACnet serve different roles. BACnet is designed for higher-level building-control objects and services, while AS-i is optimized for direct physical sensor and actuator integration.

What is AS-i Safety at Work?

AS-i Safety at Work allows safety-related field information such as emergency-stop switches, safety doors, interlocks and other safety devices to share the AS-i infrastructure with standard automation devices.

Safe and non-safe communication can therefore use the same two-conductor network when certified safety devices and the correct safety architecture are used.

Current AS-Interface safety solutions can support applications up to SIL 3 and PL e / Category 4.

This does not mean that an ordinary AS-i installation automatically becomes a SIL 3 machine. Safety transmitters, safety monitors/controllers, output devices and the complete machine safety function still need to be designed and validated correctly.

How is AS-i used in robotics?

AS-i can be useful around industrial robot cells for safety gates, proximity sensors, photoelectric sensors, valve islands and conveyor I/O.

The robot's main high-speed servo axes normally use a different real-time motion network. AS-i is more naturally positioned around the robot as a distributed I/O and safety network.

What is the difference between AS-i and PROFIBUS?

AS-i and PROFIBUS were designed for different levels of an automation architecture.

AS-i: Optimized for simple sensors, actuators, remote I/O and safety devices at the lower field level. It minimizes wiring and can carry data and power together over two conductors.

PROFIBUS DP: Designed for PLCs, remote I/O, intelligent drives and more complex field devices with greater data requirements.

The two can be used together. An AS-i gateway can collect the sensor/actuator layer and transfer its process data to a higher-level PROFIBUS controller.

What is the relationship between AS-i and Ethernet-based networks?

Modern AS-i gateways can connect to Ethernet-based plant networks such as PROFINET, EtherNet/IP or Modbus TCP.

For example, the main PLC can communicate over Ethernet while the actual machine sensors and actuators remain on AS-i.

This layered structure is common in automation: Ethernet handles controller and supervisory communication, while AS-i provides economical field wiring close to the machine.

What are the main advantages of AS-i?

Reduced wiring: Field I/O does not need to be individually wired back to the central cabinet.

Data and power on the same two conductors: Suitable devices do not require separate sensor-power and communication cables.

Flexible topology: Line, star and tree layouts are possible.

Fast installation: Profile cable and piercing technology can reduce wiring time.

Useful diagnostics: Missing devices, addressing problems and network faults can be identified through the master.

Safety integration: Standard and safety-related field devices can coexist on a properly designed AS-i network.

What are the limitations of AS-i?

AS-i is not intended to replace every industrial network. Large data transfers, video, high-bandwidth controller-to-controller communication and tightly synchronized multi-axis motion are better suited to higher-performance Ethernet or motion-control technologies.

Its strongest role is the economical connection of large numbers of distributed sensors and actuators close to the machine.

Why does an AS-i network fail to communicate?

Begin with the AS-i power supply and master diagnostics. A supply problem can affect both communication and field-device power at the same time.

Next check device addressing. A newly installed slave left at address 0, or duplicate addresses, can prevent normal commissioning.

Inspect the profile cable and piercing contacts. A module that is not fully seated on the cable may appear installed while its contacts have not correctly reached the conductors.

If the AS-i module is online but the machine signal remains incorrect, also inspect the actual sensor, actuator, local I/O indicator and any auxiliary 24 VDC supply.

Where large VFDs, servo amplifiers and switchgear are installed nearby, correct cable routing and EMC practice remain important even though AS-i is designed for harsh industrial environments.

Practical AS-i troubleshooting checklist

1. Are the AS-i master and AS-i power supply operating normally?

2. Is a newly installed device still at address 0?

3. Are there duplicate AS-i addresses?

4. Are the profile cable and piercing contacts correctly installed?

5. Is total segment length within the designed limits?

6. If repeaters or extensions are used, is the network architecture correct?

7. Do higher-power actuators have the required auxiliary supply?

8. In Safety at Work systems, have the safety monitor and safe-device diagnostics been checked?

Related Industrial Communication Pages

Industrial Communication · Ethernet · CAN · CANopen · Modbus

Related Field and Automation Pages

PLCs · HMI Panels · SCADA · Sensors · Encoders · AC Drives and VFDs · Servo Systems · Motion Control · Industrial Robotics · Power Supplies · Switchgear · Controllers · Building Automation · PLC & HMI Automation