What are the differences between DRAM and SRAM?
Two ways to hold the data a processor is working on
Dynamic RAM — DRAM and static RAM — SRAM are widely used volatile RAM technologies. Their defining difference is the storage cell: DRAM holds electrical charge, while SRAM maintains a stable state in a powered circuit. That choice affects refresh, silicon area, access behaviour and where the memory is useful. Ordinary versions of both need power to preserve their contents.
1. A charge-storage cell versus a feedback circuit
A conventional DRAM cell contains one access transistor and one capacitor. Charge leaks away, so the cells require periodic refresh before information becomes unreliable. The allowed refresh interval depends on the device and its specified temperature conditions. The controller and the memory's supported operating modes manage this requirement.
A typical CMOS SRAM cell uses a six-transistor circuit with feedback, although other cell designs exist. With its supply maintained within the specified conditions, it holds a 0 or 1 without DRAM-style periodic refresh. Static does not mean read-only, and it does not mean power-independent. A processor can repeatedly update SRAM during normal operation.
2. Neither ordinary type is persistent storage
Standard DRAM and SRAM do not guarantee data retention after their supply is removed. DRAM can also suffer data loss if refresh is not maintained while power remains available. SRAM's lack of refresh is therefore not protection against a power failure.
Battery-backed SRAM and arrangements that copy SRAM into persistent storage belong to a separate NVRAM discussion. Their protection comes from backup power, a transfer mechanism or additional non-volatile cells. Flash and EEPROM use a different approach to retain data without a supply. Retention in a sleep mode still depends on maintaining the power conditions required by that mode.
The main differences at a glance
| Property | DRAM | SRAM |
|---|---|---|
| Common cell design | One transistor and a capacitor | Typically a six-transistor circuit |
| Periodic refresh | Required | Not required |
| Retention without power | Not provided by ordinary DRAM | Not provided by ordinary SRAM |
| Density and cost per bit | Generally higher density and lower cost | Generally larger cells and higher cost |
| Access behaviour | Affected by row operations, controller scheduling and refresh | Generally suited to low-latency random access |
| Common role | Large working memory | Caches, embedded working memory and buffers |
| Power comparison | Depends on capacity, refresh and operating mode | Depends on capacity, leakage, activity and operating mode |
3. Why processors use SRAM caches and DRAM main memory
SRAM is common in processor caches and compact working areas where low access latency matters. DRAM's smaller cell makes it easier to fit more bits into a given silicon area, supporting the larger working memories of computers, phones and servers. This division of labour is a practical example of the capacity–performance balance.
SRAM's usual latency advantage does not make every SRAM connection faster than every DRAM system. External serial SRAM must receive commands and data over its interface, while a multi-channel DDR DRAM system can deliver substantial throughput. Time to service one request and volume transferred per second are different measurements. The application determines which matters most.
4. Power consumption needs a workload, not just a label
The words SRAM and DRAM are not enough to decide which uses less energy. DRAM consumes energy for refresh; SRAM consumes energy through leakage and accesses. A low-standby-current SRAM and a large high-speed SRAM have different power profiles. DRAM's low-power and self-refresh modes also depend on the particular device.
To compare energy requirements, consider the required capacity, supply voltage, temperature, access activity and data-retaining idle mode together. Comparing only the active currents of two differently sized chips does not show which performs the same job with less energy.
5. How a controller can use both
A small control board may keep measurements, variables and communication buffers in its microcontroller's internal SRAM. An advanced HMI or industrial computer handling screen images or larger datasets may use external DRAM. Individual PLCs implement different memory architectures.
Program code may reside in the ROM family or reprogrammable flash, with NAND-based storage holding a long recording history. DRAM and SRAM provide working space; persistent memory addresses a different requirement. Combining several technologies in one device follows naturally from those different jobs.
6. SDRAM and pSRAM need careful interpretation
SDRAM means synchronous dynamic RAM. A clocked interface does not turn it into SRAM; the DDR SDRAM used in computers still has dynamic cells. Synchronous SRAM products also exist. Synchronous describes interface timing rather than whether the cells need refresh.
Pseudo-static RAM — pSRAM commonly uses a DRAM array with refresh managed inside the device. A simpler external interface does not make those cells static. Refresh can introduce additional waiting on some accesses, so the chosen part's timing requirements still matter.
7. No refresh does not mean no possible faults
Both technologies need a reliability assessment covering supply conditions, temperature, timing and bit errors. Ordinary SRAM and DRAM writes are not evaluated using the same erase/program wear model as flash. That does not imply an unlimited chip lifetime. If frequently changing data must survive without power, consider FRAM, MRAM or a suitable backup arrangement separately.
Technical references: Micron — DRAM cells and density · SRAM research — 6T and 9T cells · Infineon — SRAM access and power options · Microchip — Serial SRAM and NVSRAM · Micron — Refresh and supply conditions · Infineon — pSRAM data sheet
