Protective Conductor Continuity and Connection Resistance

How is protective conductor and equipotential bonding resistance measured?
Protective conductor continuity testing checks whether exposed metal parts, such as enclosures and motor frames, have a continuous, low-resistance connection to protective earth (PE). Equipotential bonding helps reduce dangerous voltage differences between relevant conductive parts. The tester passes a known test current through the path and calculates its resistance from the voltage drop. Results are expressed in Ω or mΩ; 1 Ω = 1000 mΩ.
How does this differ from other tests?
PE continuity checks the conductive connection path. Resistance-to-earth testing examines the earth electrode and its connection to the surrounding soil; its instruments are covered by IEC 61557-5. Insulation resistance testing looks for high resistance to unwanted current paths, whereas protective bonding requires low resistance. The high-voltage mode of an insulation tester is not used for this measurement.
Earth fault loop impedance considers the complete fault loop; IEC 61557-3 covers the relevant measuring instruments. PE resistance is only part of that loop. RCD testing is another separate check: a low PE resistance reading does not establish that an RCD disconnects within the required time.
Which instrument and test current are used?
Select a low-resistance tester suitable for IEC 61557-4 measurements. Standard installation continuity testing commonly uses a test current of at least 200 mA and an open-circuit voltage of 4–24 V. A multifunction installation tester may provide this function. An ordinary, low-current multimeter continuity mode does not provide equivalent verification. Check the instrument's range, uncertainty and relevant IEC 61557 compliance.
For machine electrical equipment, the IEC 60204-1 method uses at least 0.2 A up to approximately 10 A, from an electrically separated source with a maximum 24 V AC/DC open-circuit voltage. On a machinery electrical safety tester, select the current according to the applicable procedure and equipment.
What is the measurement sequence?
1. Make the equipment safe: Testing is carried out by competent electrical personnel. Isolate mains, UPS and other supplies, prevent reconnection and safely release stored energy. Verify absence of voltage with a suitable instrument, proving that instrument on a known source before and after verification. A non-contact voltage indicator alone is insufficient. The instrument and accessories must have a suitable CAT measurement category for the location.
2. Inspect conductors and leads: Check terminals, lugs, door bonding straps, corrosion and loose connections. Test probes and leads must be sound. For two-wire measurement, perform the tester's lead-zero or compensation procedure with all extension leads included. A long test lead can have more resistance than the PE conductor being measured.
3. Connect and measure: Connect one end to the relevant PE terminal or main earthing terminal and the other to a suitable contact point on the metal part under test. Paint and oxide can prevent reliable contact; use the manufacturer's designated test point where provided. Check each relevant exposed part and bonding path separately. Record a stable reading; use DC polarity reversal according to the instrument's instructions when available.
4. Complete the checks: If readings are doubtful, inspect probe contact and connections, then repeat the test. Restore and verify any protective connections disconnected for testing before energising the equipment. Maintain test and measuring circuit safety throughout the procedure.
Two-wire or four-wire measurement?
In a two-wire test, lead and contact resistance affect the result; compensation reduces their influence. In the four-wire Kelvin method, two leads carry current while two separate leads sense voltage across the section being tested. This largely removes test-lead resistance from the reading. It is especially useful for very low-resistance connections, although instrument resolution and reliable contact still matter.
Why can parallel paths give misleading results?
Machine frames, metal pipework or cable shields may provide an alternative current path. A low reading can therefore appear even when the intended PE conductor is broken. A shielding connection in PLC, HMI and I/O equipment does not prove protective conductor integrity. Identify which path is actually being measured; where necessary, verify the conductor separately under safe isolation. Never disconnect shared PE or PEN connections casually. Four-wire testing also does not remove the parallel-path problem.
What resistance is acceptable?
There is no universal 0.1 Ω limit for every system. Assess the reading against conductor length, cross-sectional area, material, temperature and connections. Obtain the acceptance criterion from the applicable installation or product standard and test plan. A tester displaying “PASS” only shows a comparison against its configured limit.
Worked example: Near 20 °C, a 20 m copper conductor with a 2.5 mm² cross-sectional area has an approximate resistance of R = ρ × L / A = 0.0175 × 20 / 2.5 = 0.14 Ω. Here, L is the length of the conductor under test. Connection resistance adds to this value. This teaching calculation is not an acceptance limit; actual cable properties and measurement uncertainty must be considered.
The test record should identify both measurement points, test current, instrument, calibration status, lead compensation, result, acceptance criterion and any parallel paths. During initial and periodic installation verification, carry out the other required checks separately. Leakage current measurement and insulation or withstand testing do not replace this continuity test.
Technical sources: IEC 61557-4 scope · Metrel: installation continuity · Gossen Metrawatt: machine testing · Megger: low-resistance testing.