ATV 71 Fault codes 1

- AI2F (AI2 input)
Description: Non-conforming signal on analog input AI2.
Cause: The wiring of analog input AI2 or the value of the signal may be incorrect.
+ Solution: Check the wiring of analog input AI2 and the value of the signal.

- AnF (Load slipping)
Description: The encoder speed feedback does not match the reference.
Cause: This could be due to incorrect motor, gain, and stability parameters, or mechanical issues with the encoder.
+ Solution: Check the motor, gain, and stability parameters. Add a braking resistor if needed. Check the size of the motor/drive/load. Inspect the encoder's mechanical coupling and its wiring. If using the "torque control" function, refer to the note on page 187.

- bOF (DBR overload)
Description: The braking resistor is under excessive stress.
Cause: The size of the resistor may be incorrect, or it may be overheating.
+ Solution: Check the size of the resistor and wait for it to cool down. Check the [DB Resistor Power] (brP) and [DB Resistor value] (brU) parameters on page 241.

- brF (Brake feedback)
Description: The brake feedback contact does not match the brake logic control.
Cause: The brake may not be stopping the motor quickly enough.
+ Solution: Check the feedback circuit and the brake logic control circuit. Inspect the mechanical state of the brake and the brake linings.

- bUF (DB unit sh. Circuit)
Description: Short-circuit output from the braking unit or the braking unit is not connected.
Cause: There could be a wiring issue or the braking resistor might be faulty.
+ Solution: Check the wiring of the braking unit and the resistor. Inspect the braking resistor. If there is no resistor or braking unit connected to the drive, disable the monitoring of this fault by the [Brake res. fault Mgt.] (bUb) parameter on page 241.

- CrF1 (Precharge)
Description: Charging relay control fault or charging resistor damaged.
Cause: There may be an issue with the internal connections or the charging resistor.
+ Solution: Turn the drive off and then back on again. Check the internal connections. Inspect/repair the drive.

- CrF2 (Thyr. soft charge)
Description: DC bus charging fault (thyristors).
Cause: There could be a problem with the thyristors or the charging circuit.
+ Solution: Check the thyristors with [TEST THYRISTORS]. Check the IGBT with [TRANSISTOR TEST].

- ECF (Encoder coupling)
Description: Break in encoder's mechanical coupling.
Cause: There could be a mechanical failure in the encoder's coupling.
+ Solution: Check the encoder's mechanical coupling for any breaks or damage.

- EEF1 (Control Eeprom)
Description: Internal memory fault in the control card.
Cause: The issue could be due to electromagnetic compatibility or a fault in the control card's EEPROM.
+ Solution: Check the environment for electromagnetic compatibility. Turn off the drive, reset it, and return to factory settings. Inspect and repair the drive as necessary.

- EEF2 (Power Eeprom)
Description: Internal memory fault in the power card.
Cause: The power card's EEPROM may be faulty.
+ Solution: Similar to EEF1, inspect and repair the drive, focusing on the power card.

- EnF (Encoder)
Description: Encoder feedback fault.
Cause: There could be issues with the encoder's mechanical and electrical operation, its power supply, or connections.
+ Solution: Check the [Number of pulses] (PGI) and [Encoder type] (EnS) on page 79. Ensure that the encoder's mechanical and electrical operation, its power supply, and connections are all correct. If necessary, reverse the direction of rotation of the motor ([Output Ph rotation] (PHr) parameter, page 72) or the encoder signals.

- FCF1 (Out. contact. stuck)
Description: The output contactor remains closed although the opening conditions have been met.
Cause: There could be an issue with the contactor or its wiring.
+ Solution: Check the contactor and its wiring. Ensure that the feedback circuit is functioning correctly.

- HdF (IGBT desaturation)
Description: Short-circuit or grounding at the drive output.
Cause: Could be due to issues with the cables connecting the drive to the motor or the motor insulation.
+ Solution: Check the cables connecting the drive to the motor and the motor insulation. Perform diagnostic tests via the [1.10 DIAGNOSTICS] menu.

- ILF (internal com. link)
Description: Communication fault between option card and drive.
Cause: Could be due to environmental electromagnetic compatibility issues or connection problems.
+ Solution: Check the environment for electromagnetic compatibility. Check the connections. Ensure no more than 2 option cards have been installed on the drive. Replace the option card if necessary. Inspect/repair the drive.  


+ ATV 71 Fault index > 

+ ATV 71 User Manual  

+ Telemecanique 2 Homepage