IC697CHS790xSV

Nine Slot, Rear Mount - IC697CHS790 (Rear-Mounted 9 Slot Rack)

This rack is designed for industrial automation systems, perfect for larger setups. It supports both CPU and I/O modules.
Features:

    Compatibility: Accepts all IC697 PLC modules.
    Mounting Options:
        The rear-mounted rack fits into a 10-inch (254 mm) deep enclosure. In most cases, no additional cooling fans are needed.
        Front-mounted versions can be installed in standard 19-inch (480 mm) rack cabinets.
    Power Supply Options: You can use a plug-in AC or DC IC697 power supply.
    Dual Rack Operation: You can operate two racks with a single power supply using the Power Supply Extension Cable (IC697CBL700).

Functions:

    Dimensions:
        Nine-Slot Rack: Height 11.15 inches (283mm), width 19 inches (483mm), depth 7.5 inches (190mm).
        Slots: Each slot is 1.6 inches wide, and the power supply slot is 2.4 inches wide.
    Extended I/O: Two racks can be interconnected to share a single power supply, making it suitable for systems with extensive I/O needs.

Rack Mounting:

The rack must be mounted with enough space around it to allow airflow for cooling. If heat buildup could be an issue, a Rack Fan Assembly is available. There are three fan versions for different power sources:

    IC697ACC721: For 120 VAC power source.
    IC697ACC724: For 240 VAC power source.
    IC697ACC744: For 24 VDC power source.

I/O Connector:

These racks accommodate high-density I/O modules. Each module can accept #14 AWG (2.10mm²) wires. The wire bundle exits through the bottom of the terminal board cavity, where a cleat is provided to secure the bundle.
Mechanical Keying:

IC697 I/O modules are mechanically keyed to prevent incorrect module types from being inserted (e.g., inserting an AC module into a DC slot). A unique key for each module type is included. When a module is inserted into the rack, the key locks onto the center rail. This ensures that only the correct module type can be installed.
Power Supply Extension Cable:

A single power supply can support two racks using the Power Supply Extension Cable (1 meter). The cable includes +5V power and sequencing signals for proper system operation. The cable connects to a 9-pin D-type connector located on the rack’s backplane, requiring approximately 6 inches (152.4mm) of clearance on the left side.
Slot Addressing:

The IC697 PLC system allows user configuration of I/O points without DIP switches or jumpers. Configuration is done through MS-DOS or Windows programming software.
Rack Numbering:

Each rack in the system must be assigned a number from 0 to 7, with Rack 0 always reserved for the CPU rack. Rack numbers are determined by four binary-coded jumpers on the backplane, located behind the power supply.



>> GE Fanuc IC697CHS790xSV User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697CHS790xSV and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."