IC697PWR724

24 VDC, 90W Power Supply Module (IC697PWR724)

This power supply is like the heartbeat of your IC697 system, delivering all the juice your PLC modules need to run smoothly. It fits right into the rack’s leftmost slot and gives you all the essential power outputs: +5V, +12V, and -12V.
Key Features:

    Runs on 24V DC input.
    Provides 90 watts total power, spread across:
        +5V DC at up to 18 amps.
        +12V DC at 1.5 amps.
        -12V DC at 1 amp.
    Mounts easily into the rack.
    Built-in overcurrent and short circuit protection for the 5V bus.
    Can power two racks with one supply (within limits).

How It Works:

This module plugs directly into a 48-pin connector in the rack. It powers not only the main rack but can also handle a second rack as long as the total power demand stays under its 90W rating. You’ll use a pre-wired cable (IC697CBL700) for connecting the second rack.

What’s cool about this power supply is that it can keep things running smoothly even if there’s a brief power drop, up to 10 milliseconds. If something goes wrong with overcurrent or overvoltage, it’s got protective circuits to handle that without blowing a fuse (unless the fault is internal).
Dual Rack Operation:

Want to power a second rack? No problem:

    The second rack must draw less than 5.2 amps on the 5V bus.
    Only 5V power can be supplied to the second rack.
    The two racks should be close enough for the 3-foot connecting cable.

Protections:

This power supply is well-protected:

    Overvoltage Protection: If the 5V bus goes over 6.7V, the output is clamped to protect the system.
    Overcurrent Protection: Limits the current to prevent overloads (26A on the 5V, 4A on the 12V, and 2A on the -12V).
    Ride Through Time: It’ll keep running for 10 milliseconds even during a full power loss, letting the system shut down gracefully.

Mounting & Setup:

    This module is a plug-and-play, but you’ll secure it with M2.5 screws to keep it grounded and locked into place.
    The power supply door can be opened carefully from the top-left corner for easy access.

Grounding & Connections:

When connecting power, use AWG #16 to #12 wire, depending on the current load. Grounding is crucial—connect the ground terminal on the power supply to the rack’s ground and then to an earth ground using AWG #12 wire for best results.


Warnings:

    Be careful with the input terminals, as they can discharge stored energy even if the supply is switched off.
    Don’t mess with the power supply in hazardous locations unless the power is off!

Specs Recap:

    Input Voltage Range: 18 to 32V DC
    Output Power: 90W total for all outputs.
    Outputs: +5V (18A), +12V (1.5A), -12V (1A).
    Protection: Overvoltage and overcurrent protection on all outputs.

If you’re powering two racks, remember to use the Power Supply Extension Cable (IC697CBL700) for the second rack.


>> GE Fanuc IC697PWR724 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697PWR724 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."