IC697MDL651

The IC697MDL651 is a TTL, Negative Logic, 32-Point Input Module designed for industrial automation systems. It provides 32 TTL-compatible input points and does not require any user-supplied power. The module is designed for use with IC697 programmable controllers (PLCs) and offers selectable input filtering and interrupt capabilities.

Key Features:

    32 TTL-compatible input points: Configured as one group.

    No user power required: Each input has an internal pull-up resistor.

    Selectable input filter: Configurable to 1ms or 10ms.

    Interrupt capability: One input can be configured to trigger a CPU interrupt.

Technical Specifications:

    Rated Voltage: 5 volts DC.

    Inputs per Module: 32.

    Maximum Cable Length: 98.4 feet (30 meters).

    Input Isolation: 1500 volts from input to backplane.

    Input Voltage Range: -3V to +7V DC.

    Input Impedance: 5.9K ohms ±5%.

    On-state Voltage: -3V to 0.5V.

    Off-state Voltage: 2V to 7V.

    On-state Current: 1.7mA (typical) at rated voltage.

    Off-state Current: 1.1mA (maximum).

    Filter Delay: Configurable to 1ms or 10ms.

    Current Required from 5V Bus: 0.53 amps.

    VME Compatibility: Supports the VME standard.

Input Characteristics:

This module has negative logic characteristics, meaning it sinks current from the input device to the user common. The input device is connected between the power bus and the module input. It is compatible with a wide variety of input devices, including:

    Pushbuttons, limit switches, selector switches;

    Counters, BCD outputs, and other TTL-compatible outputs.

The internal 5V isolated supply and pull-up resistors on each input make it easier to use open-collector drivers and eliminate the need for user-supplied power.

Input Filter Selection:

With certain CPU options, the module’s input filter can be set to 1ms or 10ms for all points. This feature helps stabilize signal processing in environments with noise or signal fluctuations.

Interrupt Configuration:

Input point A1 can be configured to generate a CPU interrupt, triggered by the rising or falling edge of the signal. This feature is useful for real-time control applications.

Mechanical Keying:

The module includes a mechanical key that prevents incorrect placement in the rack. Once installed, the key locks onto the backplane rail, ensuring that only identical module types can be used in that slot. The key can be removed and reinserted if needed for slot relocation.

Field Wiring:

The 32 input points share a common connection, which means only one connection is required between user common and the module’s common (pin 20 or 40). Two user connections are provided for wiring convenience.

Removal Instructions:

    Firmly grasp the top and bottom of the module cover.

    Squeeze the rack clips at the back of the module to disengage it from the rail.

    Slide the module along the card guide and carefully remove it from the backplane connector.

>> GE Fanuc IC697MDL651 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697MDL651 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."