IC697MDL640

The IC697MDL640 is a 125 Volt DC Positive/Negative Logic, 16-Point Input Module used in industrial automation systems. This module provides 16 input points organized into four isolated groups, each containing four inputs. It is compatible with proximity switches and offers selectable input filtering and interrupt capabilities.

Key Features:

    16 input points: Arranged into four isolated groups of four inputs each.

    Positive/Negative Logic Compatibility: Can operate with both positive and negative logic.

    Proximity switch compatibility: Compatible with both 2-wire and 3-wire proximity switches.

    Selectable input filter: Configurable to 1ms or 10ms.

    Interrupt capability: One input can be configured to trigger a CPU interrupt.

Technical Specifications:

    Rated Voltage: 125 volts DC.

    Inputs per Module: 16 inputs (four groups of 4 inputs each).

    Input Isolation: 1500 volts RMS between input and backplane, 500 volts RMS between input groups.

    Input Voltage Range: -35V to +145V DC.

    Input Current: Typically 5mA at rated voltage.

    Input Impedance: 24.5K ohms typical.

    On-state Voltage: Positive: 90V to 145V; Negative: -20V to -90V.

    On-state Current: 3mA to 7mA.

    Off-state Voltage: Positive: -35V to +35V; Negative: V s -35V to 56V.

    Off-state Current: 0 to 2mA (minimum 2mA at 125V input).

    Filter Delay: Configurable to 1ms or 10ms.

    Power Consumption: 0.30 amps from the 5V backplane bus.

    VME Compatibility: Supports the VME standard.

Input Characteristics:

This module supports both positive and negative logic, allowing it to source or sink current from the input device to the user common. It is compatible with pushbuttons, limit switches, selector switches, and electronic proximity sensors.

    3-wire proximity switches are ideal due to their low ON-state voltage drop and low OFF-state leakage current.

    2-wire proximity switches should be carefully evaluated, as they tend to have higher ON-state voltage and OFF-state leakage current.

Input Filter Selection:

The module’s input filter is selectable and can be configured to either 1ms or 10ms for all input points. This helps ensure stable signal processing in noisy environments.

Interrupt Configuration:

When used with the IC697 CPU, input point A1 can be configured to generate a CPU interrupt, triggered on the rising or falling edge of the signal transition.

Mechanical Keying:

The module features a mechanical key that prevents incorrect placement in the rack. Once inserted, the key latches onto the backplane rail, ensuring only identical module types can be used in that slot. The key can be removed and reinserted into another slot if necessary.

Removal Instructions:

    Firmly grasp the top and bottom of the module cover.

    Squeeze the rack clips at the back to disengage the module from the rail.

    Slide the module along the card guide and carefully remove it from the backplane connector.

>> GE Fanuc IC697MDL640 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697MDL640 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."