IC697MDL253

24 Volt AC, 32-Point Input Module - IC697MDL253

The IC697MDL253 is a 24 Volt AC input module that provides 32 input points. These points are divided into four isolated groups of eight points each, allowing each group to be connected to a different phase of the AC supply.

Features

    32 Input Points: Organized into four isolated groups of eight points each.

    20 ms Input Filter: Ensures noise suppression and signal stability.

    Compatible with Proximity Switches: Works with a wide range of input devices.

    LED Indicators: Displays the ON/OFF status of each point on the logic (PLC) side of the circuit.

    Mechanical Keying: Prevents incorrect module insertion.

    Configurable I/O References: User-configurable without jumpers or DIP switches.

    Software Configuration: Configured using MS-DOS® or Windows® programming software over Ethernet TCP/IP or through the SNP port.

Functions

The 24 Volt AC Input module is designed for compatibility with a variety of input devices, such as:

    Pushbuttons, limit switches, and selector switches.

    Electronic proximity switches (both 2-wire and 3-wire).

The input circuitry ensures sufficient current for reliable operation. Typical input current is 10mA in the ON state, and the module can accept up to 2mA of leakage current in the OFF state without turning on.

For three-wire proximity switches, low voltage drop in the ON state and low leakage in the OFF state make them easily compatible. Two-wire proximity switches derive their power from the signal connection, which can result in higher ON state voltage and OFF state leakage. This module is designed to work with many two-wire devices, but each device must be evaluated for compatibility in both states.

To verify compatibility with a specific proximity switch, check the ON state characteristics of the switch against the input load line diagram. For example, a proximity switch that requires 3mA at 5V drop is compatible if it falls within the acceptable range. OFF state compatibility is assured if leakage is below 2mA at input voltage below 5V.

Module Power and Keying

The IC697MDL253 requires 0.30 amps from the 5-volt bus on the backplane. The module features mechanical keying to prevent the accidental substitution of a different module in a given slot. The key fits into a specially shaped area on the board below the connector and locks onto the backplane center rail during installation. The key remains attached when the module is removed, preventing incorrect module types from being installed in the same slot.

Field Wiring

Field wiring is simple and organized. Since each group of eight inputs is isolated, a separate wire from the power source to the power input terminal for each group is required (terminals 10, 20, 30, and 40). The detachable terminal board accepts wire sizes from #22 to #14, and two wires of the same size can be terminated on a single lug. The terminal board has enough space to route 40 #14 wires through its cavity and can be secured with a cable tie at the lower corner.

Removing an I/O Module

When removing the module from the rack, follow these steps:

    Grasp the module firmly at the top and bottom.

    Squeeze the rack clips to disengage the module from the rack rail and pull it out of the backplane connector.

    Slide the module along the card guide and remove it from the rack.

Technical Specifications

    Rated Voltage: 24 VAC, 47 to 63 Hz Sinusoidal.

    Inputs per Module: 32 (four groups of eight inputs each).

    Isolation: 1500V RMS (input to backplane), 500V RMS (between input groups).

    Input Current: 10mA typical at rated voltage.

    Input Impedance: 2.6K ohms typical.

    On-state Voltage: 13.5 to 30 volts RMS, 47 to 63 Hz.

    Off-state Voltage: 0 to 5 volts RMS.

    On-state Current: 6mA to 15mA.

    Off-state Current: 0 to 2mA (2mA minimum at 5V input).

    Filter Delay Time: 20ms typical.

    Current Required from 5VDC Backplane Bus: 0.3 amps.

This module is designed to support the VME standard C.1 and complies with various international standards for industrial environments.

The IC697MDL253 module is ideal for applications that require multiple isolated input groups, compatibility with various proximity switches, and robust electrical characteristics.

>> GE Fanuc IC697MDL253 User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC697MDL253 and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."