6EW1110-5AE
Siemens 6EW1110-5AE System Power Supply — 24 V DC Input, 5 V / 18 A Output
Siemens 6EW1110-5AE is a modular system power supply with a 24 V DC input and a 5 V DC / 18 A output. These ratings appear on the Siemens manufacturer’s nameplate. Stable low-voltage power under load is important for reliable operation of the connected control electronics.
When identifying spares for Siemens automation and SIMATIC S5 systems, assess the complete order number and hardware version together. The product is included in our SITOP power supply section, while selection must follow the unit’s own input, output and system connections.
Input, output and load capacity
Keep input and output voltage ratings separate. The nameplate’s 18 A current rating applies to the output and must not be used as the input current. Select the upstream 24 V DC power supply, cabling and protection according to their applicable technical limits. Do not apply AC mains directly to this DC input.
Multiplying the nominal nameplate values gives 5 V × 18 A = 90 W. This calculation alone does not establish input consumption or operating capacity under every ambient condition. A bench test approaching full load requires suitable load power capacity and cooling.
Interpreting the front-panel indications
The inspected front panel carries “Output voltage OK”, “24V low (Monitor)” and “Battery fault” markings. Assess output voltage, monitored load voltage and battery condition separately. An additional connection group is provided for 24 V load-voltage monitoring; distinguish it from the unit’s main DC input.
A fault indication alone does not establish that the power stage has failed. First determine which indication or monitored connection is involved. Do not add an arbitrary bridge to a monitoring connection. Obtain thresholds, pin assignments and acknowledgement instructions from the applicable service documentation.
Output measurements and testing under load
Use a suitable multimeter and the specified output reference. Do not assume protective earth and the output common are the same point. Use the front-panel points marked “5V Test” according to the wiring documentation; do not draw load current through measurement sockets.
Cable and contact resistance can cause voltage loss and heating at high current. Inspect connectors, terminals and power contacts for oxidation, looseness and discolouration. Compare the supply output with the connected board’s power input under the same load to help locate connection losses.
If the system restarts or voltage fluctuations occur, check cold startup separately from warmed-up operation. Investigate brief voltage dips and ripple with a suitable arrangement as well as measuring average DC voltage. Assess capacitors by measurement; appearance alone does not establish whether they are healthy or faulty.
Repair and protection checks
If a fitted fuse opens or the output collapses, short-circuit checks and diode measurements may be performed with the circuit de-energised. Investigate excessive demand from connected boards as well. Do not guess the fuse rating; base power-component replacement on measurements and the circuit’s actual operating conditions.
Related models and version checks
The Siemens 6EV / 6EW range includes separate order numbers such as 6EW1110-5AA, 6EW1110-5AB and 6EW1110-5AC. A shared prefix or similar enclosure does not approve direct replacement. Compare the complete code, hardware version, connection arrangement and host system.
The information in About Siemens SITOP can support a modernisation assessment. Consider the external supply, internal conversion, monitoring connections and any backup functions separately. Selecting another product with a matching voltage does not establish that every system function will be retained.
Editor’s Note
Start by identifying what each indicator is telling you. The output may appear healthy while load-voltage monitoring reports a problem. Check the monitored supply and its wiring before condemning the power supply. Bridging an input to silence the indication is not a diagnosis.
Do not reach straight for the adjustment potentiometer because the voltage is low at the board. Raising the supply voltage can conceal a loose or oxidised contact. Measure the loss between the supply and the load first. If adjustment is required, follow the manufacturer’s method under the correct load conditions.
A measurement socket is not a load connection. Connect a test load only to a verified power output using appropriately sized conductors. Testing near full load produces substantial heat; monitor load cooling, cables and contact temperatures together.
Do not replace a battery casually after seeing a battery warning. First check that the older control system has a usable program and data backup. Establish the battery type, replacement sequence and required power condition from the system documentation rather than applying another model’s battery information.
Disconnect the supply before internal repair and verify stored voltage with suitable equipment. After replacing capacitors or power components, do more than take a no-load reading. Record cold startup, gradual loading and warmed-up operation, and check that a connected board is not overstressing the supply.
OtomasyonAVM Resources and PDFs
Use the 6EW1110-5AE model page and Siemens SITOP files to find the related resources.
+ Siemens SIMATIC S5-130 / S5-150 — ST 53, 1985, German, 144 pages. Pages 8/3 and 9/9 of this family catalogue list 6EW1110-5AD. It is not a 5AE-specific service manual; do not transfer the earlier version’s tolerance, isolation or battery data to the 5AE.
Related Topics
Siemens S5 system information + Multimeter measurements + Voltage fluctuations + Capacitor checks
Used-equipment enquiries: Provide the brand, complete model, quantity, working/faulty condition, clear nameplate photographs and price. Sales are invoiced; returns are not accepted for used equipment. Workshop testing can be arranged with an agreed test scope. To offer a unit for sale, send its details to otomasyonavm@gmail.com.
Browse Categories
Used Siemens equipment + SITOP power supplies + Siemens 6EV / 6EW models + About SIMATIC S5 + SITOP PDF archive
Siemens and External References
+ Siemens ST 53 / 1985 — externally archived manufacturer catalogue
+ 6EW1110-5AE — manufacturer’s nameplate and front-panel photographs