6EV3055-0BC
Siemens 6EV3055-0BC — SINUMERIK 810 GA3 Power Supply
Siemens 6EV3055-0BC is a 24 V DC input power-supply module for SINUMERIK 810 GA3. Used in Siemens CNC control hardware, this power supply has a documented main output of +5 V / 15 A and auxiliary rails of +15 V / 0.5 A and −15 V / 0.5 A.
The item appears in our Siemens 6EV / 6EW model directory and SITOP catalogue group. Its technical identity is a SINUMERIK 810 GA3 supply. Compare the complete order number, hardware revision, connectors and machine wiring when choosing a replacement; similar-looking 6EV or 6EW modules are not automatically interchangeable.
Input and output ratings
Nominal input: 24 V DC. Permitted input: 20–30 V DC including ripple. Documented input power: 120 W. Check input voltage during startup and under load. Output current and input consumption are different quantities; the external 24 V source and cable losses also belong in the investigation.
Outputs: +5 V / 15 A, +15 V / 0.5 A, −15 V / 0.5 A. These are the limits in the manufacturer’s load calculation. Check how the CNC controller boards load each rail. Use a multimeter to verify polarity and each output separately; a present +5 V rail alone does not establish that the entire supply is healthy.
Front panel, connections and fan monitoring
X111: 24 V fan connection; X121: 24 V DC input; X131: NC ON; X141: Enable, Fan Control and Power Supply OK connections. Fan and supply status use relay contacts. Verify terminal order against the Siemens drawing when replacing connectors or power-supply connection accessories.
The supply must shut down within 1 minute after fan monitoring responds. Do not bypass protection to make a unit run when the fan is stopped or enable is missing. Investigate fan power, monitoring status and enable conditions separately.
The front panel has +5 V / 0 V measuring sockets and a +5 V adjustment. Siemens specifies a factory setting around +5.15 V to allow for cable drops. This does not justify arbitrary adjustment. For voltage fluctuations or a low reading at a board, investigate connection resistance and loading first; do not use the measuring sockets as load terminals.
Preserving machine data during a battery alarm
Alarm 1 indicates a weak backup battery; Siemens warns against switching the control off because data may be lost. Obtain readable backups of RAM contents and machine data, and follow the battery-change procedure that prevents data loss. The manual’s alarm-acknowledgement note applies from 6EV3055-0BC revision F. Establish data protection and the servicing power sequence before removing the module.
Bench testing and repair checks
Independent load testing requires verified output connections and enable conditions. By Ohm’s law, a 1 Ω load on +5 V draws approximately 5 A and dissipates 25 W. This is a partial-load example, not proof of 15 A capacity. Use a suitably cooled electronic load or a resistor with adequate power margin; never connect the load to the front measuring sockets.
The Siemens connection drawing identifies the input fuse as F118, FF 16 A, 6.3 × 32 mm. Match this against the installed revision’s markings and circuit diagram. Investigate an input short circuit before replacing a blown fuse; a higher rating or different speed class is not a remedy.
With power isolated and absence of voltage verified, inspect capacitors, rectifier diodes, connections and signs of thermal stress. These are general diagnostic candidates, not a confirmed recurring-failure list for this model. Narrow down the fault before repeated powered trials, and check earthing and chassis connections.
When buying a used power supply, request identification, revision, connector condition and a recorded load test. If supplied with used CNC control equipment, also establish the scope of the program and machine-data backup. This information page does not certify that any particular item has been tested or will directly fit an existing machine.
Editor’s Note
Start with the external 24 V source. Measure the voltage reaching the module during startup and under load. Replacing components inside the module while an upstream supply or loose terminal is responsible only prolongs diagnosis. Record the load associated with each reading.
A stopped fan calls for investigation, not bypass wiring. Check the fan, its 24 V feed, wiring and monitoring arrangement separately. Missing output while enable is absent does not by itself prove converter failure. Compare the installed wiring with the machine drawing and retain the protection.
Measure before touching the +5 V adjustment. Compare the module test point with the voltage at the powered board under the same load. Increasing the setting to hide connector or cable losses can stress other boards. Record the original setting and the reason for any authorised adjustment.
Use measurements to guide component replacement. Capacitor ESR and capacitance, rectifiers, connector solder joints and heated connections are reasonable checks. In-circuit measurements can be affected by parallel paths. Neither a clean appearance nor a discoloured component establishes the complete diagnosis.
Increase test loading in stages. Verify connections and polarity, then assess low-load operation and thermal stability. A 5 A trial is not a 15 A test report. Record auxiliary-rail behaviour, 24 V input and test duration as well; remember that a power resistor can become very hot.
Do not respond to a battery alarm by cycling machine power. Protect the working program and necessary data, and check that the backups are readable. Battery replacement and board repair may require different power sequences. After arranging data safety, isolate power for removal and repair and verify absence of voltage.
OtomasyonAVM Resources and PDFs
Browse the 6EV3055-0BC model page and Siemens 6EV / 6EW used-model directory.
Siemens SITOP files — our common document page for this project.
SINUMERIK 810 / 820 GA3 — Installation Instructions, 6ZB5 410-0DL02 (English, 01.93, 413 pages). Relevant printed pages: 3–4, 4–1, 11–7; PDF pages: 34, 58, 356.
SINUMERIK 810 / 820 GA3 — Connection Conditions, 6ZB5 410-0DV02 (English, cover edition 07.94, 128 pages). Relevant printed pages: 1–9, 1–36; PDF pages: 17, 44.
Related Topics
Related reading: CNC controller boards, voltage fluctuations, memory data loss and multimeter measurements.
Browse Siemens and CNC Equipment
+ Siemens second-hand catalogue
External References
Siemens — SINUMERIK 810 / 820 GA3 Connection Conditions — manufacturer PDF server.
Siemens — SINUMERIK 810 / 820 GA3 Installation Instructions — manufacturer manual archived by device.report.