6EV3054-0GC
Siemens 6EV3054-0GC SINUMERIK / SIROTEC Power Supply
Siemens 6EV3054-0GC is a 24 V DC input, 5 V DC / 25 A output power supply specified for SIROTEC RCM/ACR and SINUMERIK 3 / 805 SM systems. It supplies electronics in legacy CNC control systems. These nominal ratings appear in the Siemens datasheet bearing the complete model reference.
Browse this unit within our Siemens 6EV / 6EW models and SITOP power supply categories. Selection depends on the machine’s control system and the complete hardware reference. Our Siemens SITOP overview provides context for comparing the broader product groups.
Input, output and measurement points
Input: 24 V DC. Output: 5 V DC, nominally 25 A. Match the voltage and current ratings to the nameplate before connecting the unit. Assess the incoming 24 V supply separately from the 5 V supply delivered to the control boards.
The 805SM-P manual shows +5 V / 0 V test sockets, a +5 V adjustment potentiometer and a hardware Reset button. Use a multimeter for output checks; investigate the cause of a voltage drop before changing the adjustment.
24 V connections, Enable and NC-ON
The documented assignments are C1: +24 V; D1: 0 V; E–F: Enable; G–H: NC-ON. Enable is required for startup. Terminate the NC-ON cable shield at the specified grounding terminal.
Trace the machine wiring diagram to establish how Enable is provided. Check the relay contact, wiring and control logic together. Where a PLC manages the circuit, verify that the start command reaches the supply as part of the diagnosis.
Battery module and revision checks
The 805SM-P manual documents a battery module containing three 1.5 V LR6/AA cells. Check the actual holder and hardware revision before replacement. Assess battery servicing separately from the main power-output test, and secure a data backup before removal.
6EV3054-0CC, 6EV3054-0DC and 6EV3054-0FC are other references in the same code family. A shared family designation does not establish interchangeability. Compare the complete suffix, connector arrangement, control connections and machine hardware list.
Editor’s note
Before working on a used CNC controller, secure a usable program, parameter and machine-data backup. Avoid casual power cycling when the battery history is unknown. A reliable backup can be as valuable as the power-supply repair itself.
For low voltage or repeated restarts, begin by checking the incoming 24 V under load. Voltage fluctuations, loose terminals or worn supply connections may be responsible. Compare the supply output with the voltage arriving at the boards; investigate connection losses before adjusting the supply.
A no-load voltage reading is only an initial check. Once the wiring and starting conditions are established, record cold startup, warming and voltage regulation under a suitable load. Investigate excessive board current if the output collapses. Before oscilloscope ripple measurements, ensure that the probe’s ground connection cannot short the measurement point.
If the battery holder shows leakage or corrosion, inspect the contact springs and nearby tracks as well as replacing the cells. Use the correct battery type verified against the equipment information. Adding a different cell chemistry or an external charging arrangement can introduce another fault.
For internal repairs, isolate power and measure to confirm that capacitor voltage has discharged. Check power semiconductors, rectifiers, electrolytic capacitance/ESR, cracked joints and overheated connectors. An undistorted capacitor case does not establish electrical health; base replacement decisions on measurements.
During CNC maintenance, photograph the wiring and complete nameplate before removal. When assessing used Siemens equipment, request the load, test duration and measured values behind a “working” description. After refitting, verify control startup, data retention and the machine’s normal operating sequence.
OtomasyonAVM resources and PDFs
Use our Siemens 6EV / 6EW main page for the product group and Siemens SITOP files for documentation.
+ Siemens 6EV3054-0GC datasheet – English, 28 April 2018, 1 page.
+ SINUMERIK 805SM-P connection guide – English, 05.94, 186 pages. Model section: 3.1.4.2; printed 3-6 / 3-7, PDF 33 / 34.
These documents cover product identification and system connections; they are not presented as component-level repair schematics.
Related topics
+ CNC control systems + Multimeter measurements + CNC machine maintenance + Voltage fluctuations
Used-equipment enquiries: Provide the brand, complete model, quantity, working/faulty condition, nameplate photographs and asking price. Sales are invoiced; returns are not accepted for used equipment. Workshop testing is possible where suitable conditions are available. To offer equipment for sale, send its details to otomasyonavm@gmail.com.
Browse categories
+ Siemens 6EV / 6EW models + SITOP power supplies + Used Siemens equipment + Used CNC controllers + SITOP PDF archive
Siemens and external references
+ Original Siemens 6EV3054-0GC datasheet copy. Publisher: Siemens; file host: EU Automation.
+ Siemens SINUMERIK 805SM-P Interface Description, Part 2: Connection Conditions.