6EV1352-5BK00

Siemens 6EV1352-5BK00 Three-Phase 24 V DC / 20 A Power Supply

Siemens 6EV1352-5BK00 is a power supply providing +24 V DC / 20 A from a three-phase mains supply. SINUMERIK 805 and 880 documentation identifies it as an external supply, with the SINUMERIK ordering reference 6FC9304-0AC. Use the complete hardware code together with the machine diagram when assessing the supply arrangement of a legacy CNC control system.

Browse this model in our Siemens 6EV / 6EW archive and SITOP power supply section. Our Siemens SITOP overview provides broader product-group context. Replacement assessment must cover input connections, output behaviour and mechanical arrangement together.

Three-phase input and voltage taps

The manufacturer’s connection table specifies delta configurations for 220 / 240 / 254 V and star configurations for 380 / 415 / 440 V. These require different terminal and jumper selections. Do not treat them as a continuous input range available without changing the connections.

Compare the actual mains voltage, nameplate and installed jumpers before connection. Correct tap selection matters alongside the load’s current requirement. Verify the jumper arrangement with power isolated, using the applicable manufacturer drawing.

24 V output and measurements

The drawing identifies 11 C2 as +24 V and 11 D2 as 0 V. The transformer–rectifier arrangement shown supports assessing the unit as an unregulated supply. Evaluate its response to mains and load changes against the permitted input range of the connected equipment.

Use a multimeter to record no-load and loaded conditions separately. Establish the connection between circuit 0 V and protective earth from the machine diagram before selecting a measurement reference.

Mechanical arrangement and model comparisons

The manufacturer drawing shows 482.3 mm front width, 132.5 mm height and M6 screw connections. Check cable lugs, terminal access and service clearance on the actual unit.

6EV1322-7AK00, 6EV1334-4AK00, 6EV1336-5AK and 6EV1363-5AK are other 6EV supply references to review. Verify input phase count, capacity and connections for each model; the shared family designation does not establish interchangeability.

Editor’s note

Before removing a supply from a used CNC control cabinet, photograph the nameplate, input tap selection and every jumper, then identify the cables. Check previous modifications against the documentation. Starting here can prevent unnecessary component replacement.

If the output is weak, verify that all three phases reach the unit. Inspect fuses, control relays, contactors and connection points together. A missing phase or poor contact can resemble a rectifier fault when only the DC output is checked.

For low voltage or fluctuations, verify input selection, then record no-load and loaded behaviour. Account for the supply’s construction when assessing voltage regulation. Compare readings with the connected control equipment’s acceptance limits instead of assuming a normal value.

Before internal repairs, isolate power and measure to confirm that capacitor voltage has discharged. Inspect rectifier diodes, filter capacitors and overheated connections. For transformer humming or heating, investigate incorrect tap selection, phase loss and overload as well. Find the cause of an open fuse before replacement; do not increase its rating as a repair.

Where supply connections show discoloration, loose lugs or corrosion, assess both the cable and the contact surface. Measuring at the supply and at the load under the same operating conditions helps identify connection losses.

After CNC maintenance, or when accepting used Siemens equipment, record startup and warm operation under a suitable load. Include voltage, load current, ripple and duration. A no-load voltage reading alone does not establish dependable operation in the machine.

OtomasyonAVM resources and PDFs

Use our Siemens 6EV / 6EW models for the product group and Siemens SITOP files for documentation.

+ SINUMERIK 805 SW4 connection guide – English, 05.93, 162 pages. Exact model, connections and dimensions: section 4.8.2, printed 4-71 / PDF 122. The relevant page retains revision 11.91.

+ SINUMERIK 880 connection guide – English, 05.91, 218 pages. Exact model and connection drawing: section 6.1.2, printed 6-2 / PDF 141.

Related topics

+ CNC control systems + Multimeter measurements + Protective grounding + Voltage fluctuations

Used-equipment enquiries: Provide the brand, complete model, quantity, working/faulty condition, nameplate photographs and asking price. Sales are invoiced; returns are not accepted for used equipment. Workshop testing is possible where suitable conditions are available. To offer equipment for sale, send its details to otomasyonavm@gmail.com.

Browse categories

+ Siemens 6EV / 6EW models + SITOP power supplies + Used Siemens equipment + Used CNC controllers + SITOP PDF archive

Siemens and external references

+ Copy of the original Siemens SINUMERIK 805 SW4 connection guide. Publisher: Siemens; file host: ADEGIS.

+ Siemens SINUMERIK 880 Interface Description, Part 2: Connection Conditions.