6ES7 195-7HD10-0XA0

Siemens automation › SIMATIC S7 › Siemens ET 200 › 6ES7195-7HD10-0XA0

Siemens 6ES7 195-7HD10-0XA0 ET 200M BM IM/IM Active Bus Module

6ES7 195-7HD10-0XA0 is a BM IM/IM active bus module for two compatible IM 153-2 interface modules in redundant ET 200M applications. It provides the interface modules' backplane connection within Siemens ET 200 distributed I/O systems. This order number identifies the bus module; the IM modules installed on it are separate components.

A shared base for two interface modules

A redundant station requires a suitable base and correct hardware configuration alongside its two IM modules. When reviewing the ET 200 system architecture, include the controller, IM pair and bus module in the same parts list. Do not assume that every product in the PROFIBUS and PROFINET interfaces category fits this base. Check the complete IM 153-2 order number and applicable compatibility table.

Distinguishing similar bus modules

BM PS/IM 6ES7195-7HA00-0XA0 accommodates a power supply and one interface, while BM IM/IM 6ES7195-7HD10-0XA0 accommodates two interfaces. 6ES7195-7HD80-0XA0 is the Outdoor version for extended environmental conditions. When selecting ET 200 connection modules, check more than physical appearance or the description “IM base”.

BM IM/IM also supports the two interfaces in suitable DP/PA Link and Y-Link assemblies. A Y-Link has a separate bus module for its Y-coupler. Keep the roles of ET 200 terminal blocks and active backplane modules distinct in the parts list.

Dimensions, mounting rail and replacement conditions

Dimensions are 97 × 92 × 30 mm (width × height × depth), with an approximate weight of 133 g. Active bus modules require the special ET 200M mounting rail intended for module changes during operation. Allow space for the installed IM modules and PROFIBUS connectors in addition to the base dimensions.

The bus module itself must only be removed when de-energized. The removal/insertion function during RUN must not be extended to replacement of the base. Identify supply paths through the ET 200 power supply modules and power distribution components when preparing the maintenance plan.

Five checks before selection or replacement

1. Exact order number: Verify 6ES7195-7HD10-0XA0 on the label. Do not automatically treat the older 7HD00, standard 7HD10 and Outdoor 7HD80 versions as interchangeable.

2. IM pairing: Record both interface order numbers, hardware revisions and firmware versions. Physical fit alone does not establish redundancy compatibility; check the pairing permitted by the installed system.

3. Remaining station modules: Identify the bases used for ET 200 digital input modules, ET 200 digital output modules and ET 200 analog input modules separately. The two BM IM/IM positions are for interfaces and do not replace the bases required by signal modules.

4. Mechanical condition: Inspect rail locks, side connections and backplane contacts. Check that unused positions and the final bus module have the appropriate covers.

5. Post-maintenance verification: Following the planned shutdown, check station startup, diagnostics from both interfaces and redundant switchover behavior. Retain the original hardware project and diagnostic records for comparison.

Editor's note: If both IM modules show similar communication faults, include the shared bus module, contacts, mounting and supply arrangement in the investigation. Photographs and diagnostic records taken before replacement help avoid repeatedly investigating the same fault by changing different components.

Manuals and PDF documentation

Visit the Siemens ET 200 PDF documentation and user manuals page for the ET 200M Operating Instructions. Review active bus module installation, IM 153-2 compatibility tables and the Replacing the bus module section. For DP/PA Link or Y-Link applications, also consult the corresponding connection-system manual.

Related topics

Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules

Explore the station: About ET 200 · Communication interfaces · ET 200 manuals

Otomasyon AVM | Siemens:
Siemens main menu  |  Siemens S7 PLC  |  SIMATIC S7  |  ET 200 modules