6ES7 194-4AF00-0AA0
Siemens Main Menu › SIMATIC S7 › ET 200 Modules
Siemens 6ES7 194-4AF00-0AA0 — ET 200pro CM IM PN PP Cu Connection Module
6ES7 194-4AF00-0AA0 is the CM IM PN PP Cu connection module for ET 200pro, part of the Siemens ET 200 family. It fits onto an IM 154-4 PN High Feature interface and provides copper PROFINET connections and a 24 V DC supply entry. This component in the ET 200 connection module range operates together with the interface electronics.
Interface compatibility and connections
Siemens documents pair it with 6ES7154-4AB10-0AB0 / IM 154-4 PN HF. When selecting PROFIBUS and PROFINET interfaces, check the connection module as well as the network type. This version has two Push-Pull RJ45 network sockets and two Push-Pull power sockets. The power sockets are separate from the RJ45 data connections.
X02 P1/P2 provide PROFINET connections, X03 receives the supply and X04 forwards it. Network forwarding uses the switch integrated into the IM interface. Match your industrial cables and connectors to the Push-Pull locking and sealing arrangement; an ordinary RJ45 plug fitting into the socket does not establish suitability for field conditions.
Dimensions and supply limits
Dimensions: 90 × 130 × 51 mm (width × height × depth). 1L+ is the electronics/sensor supply; 2L+ is the load supply. The maximum feed current for each supply is 16 A up to 40 °C and 8 A up to 55 °C, subject also to the cable's permitted current capacity.
The ET 200pro internal busbars have separate limits of 5 A for 1L+ and 10 A for 2L+. When planning power distribution and potential groups, account for incoming current, station consumption and current forwarded downstream. A larger 24 V DC power supply does not increase these limits; the lowest applicable limit governs the design.
The difference between 4AF00 and 4AG00
6ES7194-4AF00-0AA0 / PP Cu uses copper RJ45 connections. 6ES7194-4AG00-0AA0 / PP FO uses SC RJ fiber-optic connections. They cannot be exchanged while retaining the same network cable. Specify the complete order number and installed connector type instead of ordering only an “ET 200pro PROFINET connection module.”
Five checks before selection
1. Interface order number: When reviewing the ET 200 system architecture, record the exact IM module code. List the CM connection module and IM interface separately in the delivery requirements.
2. Separate supply paths: Do not treat the sensor supply for digital input modules and the load supply for digital output modules as the same fault point. Working communication does not prove that 2L+ is healthy.
3. Current and temperature: Measure the downstream load and ambient temperature. If necessary, redesign the supply arrangement using suitable ET 200 power supply modules; the presence of forwarding connectors does not permit an unlimited supply chain.
4. Locking and protection: Check that plugs latch fully, seals are intact and unused sockets have suitable caps. Siemens requires unused sockets in this Push-Pull arrangement to be capped to achieve IP65 protection.
5. Maintenance impact: Identify the affected downstream stations before disconnecting network or power forwarding. Switch off both 1L+ and 2L+ before inserting or removing the power connectors.
Editor's Note
Plan maintenance beyond the station carrying this connection module. If connections continue through P2 or X04, disconnecting them can affect downstream stations as well. Record the network and power routes separately before replacement. Labeling cables beforehand is easier than tracing incorrect connections during recommissioning.
PDF and connection information: Use pages 96–99 and 260–261 of ET 200pro Operating Instructions, A5E00335544-AJ alongside our Siemens ET 200 manuals and PDF documents page. Siemens connector guide 50102465 also helps identify suitable plugs and accessories.
Related Topics
Connection Modules · Communication Interfaces · Power Supply Modules · Terminal Blocks
Otomasyon AVM
Siemens Main Menu · SIMATIC S7 · ET 200 Modules · ET 200 PDF Manuals · PLC and HMI