6ES7 132-7RD01-0AB0

Siemens Main Menu › SIMATIC S7 › ET 200 Modules

Siemens 6ES7 132-7RD01-0AB0 — ET 200iSP 4 DO, 23.1 V / 20 mA, H Shutdown Module

6ES7 132-7RD01-0AB0 is a four-channel digital output module for intrinsically safe field circuits in the ET 200iSP series of the Siemens ET 200 distributed I/O family. It operates suitable Ex i solenoid valves, DC relays and actuators. Among ET 200 digital output modules, it is identified by its 23.1 V DC / 20 mA rating and SHUT DOWN “H” function.

Understanding the 23.1 V / 20 mA rating

23.1 V is the no-load output voltage. Siemens specifies an internal resistance of 275 Ω and an output characteristic corner point E of at least 17.6 V / 20 mA. Select a valve using its pickup and holding requirements together with cable losses, rather than its “24 V coil” label alone. 20 mA does not indicate an analog 4–20 mA control signal; this is an on/off output module.

Connecting two outputs in parallel is not supported on this version. Do not apply the increased-current wiring available on certain 17.4 V variants to the 7RD01. A load requiring more current needs a module with an appropriate output characteristic.

How H shutdown works

An active-high, intrinsically safe signal at the external shutdown input switches off all four outputs together. This operation does not change the PLC output process image. The program may therefore show an output command of “1” while the field load is de-energized. H and L shutdown versions require the correct wiring and signal logic.

Intrinsic safety for explosion protection and functional safety are separate requirements. A shutdown input does not automatically make this an F-DO module. Assess the safety architecture separately when the project requires ET 200 fail-safe modules and PROFIsafe safety communication.

Terminal and station arrangement

Suitable terminal families are TM-IM/EM 60S, TM-IM/EM 60C, TM-EM/EM 60S and TM-EM/EM 60C. Verify the ET 200iSP series when selecting ET 200 terminal blocks. When checking connection modules and field wiring, trace the output connections separately from the external shutdown circuit.

Five checks before selection

1. Complete model and series: Confirm 7RD01 on the label. Identify the ET 200iSP station using the ET 200 system and product family guide. The 17.4 V / 27 mA 7RD11 and 17.4 V / 40 mA 7RD22 are not automatically interchangeable with this model.

2. Load and Ex suitability: Check the actuator’s electrical requirements and Ex documentation. Verify the intrinsic safety parameters of the module, cable and field device together; similar voltage and current ratings alone do not establish suitability.

3. Supply and interface: Compare the capacity of the ET 200 power supply modules with the station load. When reviewing ET 200 communication interfaces, check the installed interface module against the hardware configuration.

4. Shutdown circuit: Verify the external signal source, H logic and wiring diagram. Do not bypass this input with a jumper or an arbitrary voltage during troubleshooting.

5. Functional checks: Test all four channels and the common shutdown function during controlled commissioning. Where available, monitor feedback through the ET 200 digital input modules to confirm actual valve movement; the PLC command bit alone is insufficient.

Editor’s Note

If the PLC output is on but the valve does not operate, check three things separately: the output command, the external H shutdown signal and the load’s actual electrical requirements. For faults appearing after coil replacement, compare the operating data of both coils, not just their voltage labels. Follow the site’s hazardous-area procedures for measurements and intervention.

PDF manuals and wiring: Visit the Siemens ET 200 user manuals and PDF documentation page. Section 12.2 of ET 200iSP Operating Instructions, A5E00247483-AH, 10/2019 covers this output family; pages 266–268 cover load selection and parallel connection information. Also use current Ex documents applicable to the device version and installation region.