6ES7 131-1BH01-0XB0
Siemens 6ES7 131-1BH01-0XB0 – ET 200L 16DI 24 V DC Digital Input Electronics Block
Siemens 6ES7 131-1BH01-0XB0 is a 16-channel, 24 V DC digital input electronics block for SIMATIC ET 200L. It transfers signals from sensors, pushbuttons and position switches to the control system through PROFIBUS-DP. Typical uses include collecting signals from one machine section and replacing the electronics in an existing ET 200L station. Explore the Siemens ET 200 family and our ET 200 digital input modules for related products.
These inputs can monitor product presence on a conveyor, mechanism positions or auxiliary contact states. Clearly labelling the connected sensors and photoelectric sensors helps maintenance staff relate each electrical signal to the corresponding machine operation.
ET 200L Construction and TB 16L Compatibility
The electronics block requires a TB 16L terminal base. Compatible versions are 6ES7 193-1CH00-0XA0 with screw terminals and 6ES7 193-1CH10-0XA0 with spring terminals. Field wiring remains on the base when the electronics are replaced. Replacement must be performed with the power switched off, following the manufacturer's removal and installation procedure. See our ET 200 terminal blocks for connection options.
This model uses the ET 200L architecture and does not support Smart Connect expansion. Match the complete electronics-block code, terminal base and project device definition when selecting a replacement. For additional wiring points, check suitable ET 200 additional modules and terminal accessories against the installed base.
Input Characteristics and Signal Duration
The specified signal ranges are +13 to +30 V for logic “1” and −30 to +5 V for logic “0”. Typical active-input current is 5 mA. Two-wire sensors may have a maximum quiescent current of 1.5 mA. When replacing a sensor, check its output circuit and off-state leakage. Signals obtained through a relay contact also require a circuit that establishes the expected input voltage.
Input delay is 2–4.5 ms in both transition directions. Assess brief pulses together with the communication and PLC cycle times. If a small passing object is detected at reduced machine speed but missed during normal production, measure the actual sensor pulse first. Applications requiring continuous high-speed counting should also be assessed against suitable ET 200 function modules.
PROFIBUS-DP Connection and Commissioning
The maximum communication rate is 1.5 Mbit/s. Two rotary switches set the PROFIBUS station address within 1–99. Record the existing address before fitting a replacement so it can be checked against the project. Our PROFIBUS and PROFINET overview explains the network concepts, while the ET 200 communication interfaces page covers related equipment.
During commissioning, compare the device configuration, station address and PLC input mapping. If a sensor is active but the expected program bit remains unchanged, compare the local channel indicator with the online input value. Following the signal through the wiring, network and program address helps keep troubleshooting focused.
Power Distribution and Field Wiring
The sixteen inputs are arranged in two groups of eight. Check the electronics supply and field-group supplies against the terminal diagram. When several signals in the same group disappear together, inspect the relevant 24 V power supply, fuses and supply connections before replacing individual sensors.
The inputs are electrically isolated from PROFIBUS-DP; individual input channels are not isolated from each other. Include grounding, cable shields and sensor connectors in the inspection. For intermittent problems, measurements taken while the relevant machine loads are operating can reveal conditions that are absent during a static check.
Indicators, Installation and Physical Data
Green channel LEDs show input states, green ON indicates the electronics supply and red BF indicates a bus fault. Hardware interrupts are not supported. When designing maintenance screens, distinguish an inactive field signal from a station communication failure. Clear descriptions on the HMI or SCADA display help operators report the actual condition.
Electronics-block dimensions are 145 × 60 × 60.5 mm, approximate weight is 130 g and typical power loss is 2.2 W. Protection is IP20. Operating temperature is 0 to +60 °C horizontally and 0 to +40 °C in other mounting orientations. Cabinet planning must also allow space for the terminal base, bus connector and cable bends.
Editor's Recommendation
Start by identifying the extent of the fault: Is one input missing, has a group of inputs disappeared, or is the entire station inaccessible? Each condition points towards different checks. Before deciding to replace the electronics, inspect the supply, terminal contacts and PROFIBUS connection. Include the complete product code, terminal-base label and existing station address in a replacement enquiry to help establish the correct match.
Product Selection and Technical Documentation
Use the complete order number, 6ES7131-1BH01-0XB0, when matching the product. The quotation should identify whether the electronics block, TB 16L base and bus connector are included. For wiring and commissioning information, consult the ET 200L documentation through our Siemens ET 200 manuals page. The relevant system manual is EWA-4NEB 780600902-05; section 8.1 covers this electronics block.
Related Topics
About Siemens ET 200 · ET 200 digital output modules · ET 200 connection modules
Siemens > SIMATIC S7 > ET 200