6ES7 193-7CA10-0AA0

Siemens automation › SIMATIC S7 › Siemens ET 200 › TM-EM/EM60C

Siemens 6ES7 193-7CA10-0AA0 — ET 200iSP TM-EM/EM60C Terminal Module

The 6ES7 193-7CA10-0AA0 is a TM-EM/EM60C terminal module for ET 200iSP, part of the Siemens ET 200 distributed I/O family. It accommodates two electronic modules and has blue spring-loaded terminals. Within the ET 200 terminal block range, this component provides the field wiring base; the electronic modules that process the signals are selected separately.

Two slots do not mean two channels

The base has two module slots, not two signal channels. Channel count and signal type depend on the electronic modules installed. When reviewing ET 200 digital input modules, ET 200 analog input modules and ET 200 digital output modules, first confirm the ET 200iSP subfamily and complete order numbers. Products listed under the wider ET 200 range are not automatically compatible with this base.

Spring-loaded, screw and push-in terminals

6ES7193-7CA10-0AA0 uses spring-loaded terminals. 6ES7193-7CA00-0AA0 has blue screw-type terminals, while 6ES7193-7CA11-0AA0 has blue push-in terminals. In particular, do not treat CA10 and CA11 as identical connection systems. When selecting ET 200 connection components, follow the specific terminal instructions for conductor preparation and connection.

The 6ES7193-7CA20-0AA0 variant has black screw-type terminals and is offered for use in safe areas to identify non-intrinsically safe signals. Terminal colour therefore has a purpose beyond appearance.

Station layout and the roles of different bases

Within the ET 200 station architecture, TM-EM/EM bases are positioned to the right of the TM-IM/EM or TM-IM/IM terminal group. Bases for PROFIBUS and PROFINET interface modules and ET 200 power supply modules serve different purposes. The 2 DO Relay UC60V/2A output module uses the dedicated TM-RM/RM 6ES7193-7CB00-0AA0 terminal base; check this exception when selecting relay outputs.

Dimensions and application requirements

Siemens specifies dimensions of 60 × 190 × 52 mm (width × height × depth) and an approximate weight of 275 g. Allow additional installation space for the fitted electronic modules and cable routing rather than using the terminal base dimensions alone.

Explosion protection suitability and functional safety are separate considerations. In projects using ET 200 safety modules, the safety function must be assessed through the relevant module, controller and application. Blue terminals or the base's certification alone do not establish the suitability of the entire circuit; field devices, wiring and enclosure requirements must also be checked.

Five checks before ordering or replacement

1. Identification: Confirm the full order number 6ES7193-7CA10-0AA0. Do not confuse it with the CA00, CA11 or CA20 variants.

2. Installed modules: Record the order numbers of the electronic modules in both slots. Compare terminal numbers and field wiring with the wiring diagrams for those modules.

3. Connection condition: Inspect the spring terminals, contacts, locking points and housing. Investigate damage, looseness, corrosion or signs of overheating.

4. Installation space: Check rail placement, connections to adjacent bases and cable routing. A matching 60 mm width alone does not establish mechanical compatibility.

5. Scope of supply: Confirm whether the quotation covers the terminal base only or includes electronic modules. Do not assume that every fitted component shown in a photograph is included.

Editor's note: An apparent input or output fault is not always caused by the electronic module; a terminal connection or contact problem can produce a similar symptom. Before planning a replacement, record the electronic module number, terminal base number and affected terminal positions together. When buying a CA10 base, pay particular attention to the mechanical condition of its spring terminals. A clean housing alone does not guarantee sound connections.

Manuals and PDF documents

For wiring diagrams, terminal layouts and installation requirements, visit the Siemens ET 200 PDF and user manuals page. The relevant documents are the 6ES7193-7CA10-0AA0 technical data sheet and ET 200iSP Operating Instructions. Read the wiring instructions for the selected electronic modules alongside the terminal base documentation.

Related topics

Power and connections: Power supply modules · Terminal blocks · Connection modules · Power distribution modules

Explore the station: About ET 200 · Communication interfaces · ET 200 manuals

Otomasyon AVM | Siemens:
Siemens main menu  |  Siemens S7 PLC  |  SIMATIC S7  |  ET 200 modules