6ES7 193-1CH10-0XA0
Siemens 6ES7 193-1CH10-0XA0 – ET 200L TB16L Spring-Type Terminal Block
The Siemens 6ES7 193-1CH10-0XA0 is a 16-channel TB16L terminal block with spring connections for SIMATIC ET 200L stations. Within the ET 200 range, it provides the main base for field wiring and the compatible plug-in electronic block. When identifying a replacement, check both the TB16L designation and the 1CH10 suffix, which identifies the spring-type version.
A terminal block provides the physical connections between field wiring and the electronics. Reading inputs or switching outputs takes place in the installed electronic block. This distinction matters when servicing an older machine: the wiring base can remain sound while the electronics fail, or a poor terminal connection can interrupt a signal even when the electronics are working.
Compatible electronic blocks
The Siemens manual lists 6ES7131-1BH01-0XB0 — 16 DI, 24 V DC and 6ES7132-1BH00-0XB0 — 16 DO, 24 V DC/0.5 A for the TB16L. The first provides digital inputs; the second provides digital outputs. The 0.5 A figure belongs to the specified output electronic block’s channel rating. It should not be treated as a universal current rating for every connection on the terminal base.
The station configuration in the PLC project must match the installed electronics. A TB16L label alone does not identify the station as an input or output unit. PROFIBUS communication and station addressing are also handled through the electronic assembly; the terminal base has no independent network address or firmware installation.
Channel count and terminal numbering
Terminals 1–8 and 9–16 carry the signals for the two channel groups. The purpose of terminals 17–24 and 25–32 depends on the installed electronic block: they provide sensor supply connections in the input arrangement and the corresponding M connections in the output arrangement. Seeing 32 numbered terminals therefore does not mean that the base provides 32 independent I/O channels.
Read the terminal numbers together with the wiring diagram on the electronic block. If previous repairs have changed the wiring, conductor colours alone are not enough to establish the connection. Trace the supply, common and signal conductors of each inductive sensor, and check PNP/NPN and sinking/sourcing compatibility between the sensor and the electronic input circuit.
Supply groups and internal bridges
In the Siemens terminal assignment, 1L+ supplies channel group A. 2L+ and 3L+ serve group B and are internally connected to each other. 4L+ and 5L+ supply the electronics and are also internally connected. All M terminals, from 1M to 5M, are connected internally. Understanding these bridges helps avoid incorrect conclusions when measuring connections or transferring wiring.
Check the external power supply, channel groups and electronics supply against the actual station diagram. Common M terminals do not mean that all L+ terminals form one common supply rail. M/0 V and PE also have different purposes; the protective earth connection must not be used as a substitute for the control circuit’s return conductor.
Spring connections and conductor preparation
This version clamps the conductor using a spring mechanism. The Siemens wiring table specifies 0.14–1.5 mm² conductors for the standard field connections. The spring-terminal installation instructions specify an 11 mm stripping length and a 0.5 × 3.5 mm screwdriver. The screwdriver opens the spring through its operating aperture, while the conductor enters the separate wire opening. Removing the screwdriver allows the spring to grip the conductor.
Forcing a wire into the opening is not a substitute for releasing the spring. Prevent loose strands, insulation trapped in the contact area and excessive exposed copper. Any ferrule must suit both the conductor and the terminal’s permitted dimensions. Arrange the cables and connectors so that they do not place tension on the termination.
A screw-terminal tightening torque does not apply to this model’s spring field connections. The spring operating aperture is not a tightening screw. A damaged mechanism or a terminal that no longer retains the conductor should not be forced with a screwdriver in an attempt to restore its grip.
Mounting, dimensions and maintenance
The TB16L mounts on a suitable 35 mm DIN rail. The Siemens manual gives terminal-block dimensions of 145 × 100 × 40.5 mm. With the electronic block and the specified PROFIBUS connector installed, the required depth from the top of the rail reaches 82 mm. Allow additional space for cable routing and bend radius. The Siemens product record for this exact order number lists a net weight of 0.225 kg.
Field wiring remains on the terminal base when a compatible electronic block is replaced, so the entire set of field conductors does not normally need to be disconnected for that operation. Replacing the terminal base itself requires the conductors to be identified and transferred correctly. Safely isolate the relevant circuits and verify absence of voltage before beginning work.
During maintenance, inspect more than the exterior. Check conductor retention, the contacts that mate with the electronics, the rail latch and the condition of the housing. In an automation system, an intermittent signal can originate in a termination, sensor, supply circuit or electronic block. Replacing parts before locating the fault can leave the original problem unresolved.
Similar models and spare-part selection
6ES7193-1CH00-0XA0 is the screw-type TB16L. The 6ES7193-1CH10-0XA0 covered here is the spring-type version. Order number 6ES7193-1CL10-0XA0 identifies the 32-channel TB32L spring-type base. Pay particular attention to the CH versus CL distinction: the channel arrangement and physical dimensions differ.
The Siemens product record lists PM500 lifecycle status from 1 October 2024, with no direct successor identified. Select a replacement using the complete order number, connection method, installed electronic block and condition of the individual part. Similar appearance alone does not establish compatibility with terminal hardware from another ET 200 subfamily.
Editor’s note: Read both labels first: the order number on the TB16L base and the number on the electronic block above it. “16-channel ET 200” is not enough to identify the required spare. Establish the connection method, the input or output function, and which part of the assembly is actually faulty.
Manuals and PDF documents
Use the Siemens ET 200 user manuals and PDF documents page for the documentation archive. This model is covered in section 7.1 of ET 200L Distributed I/O Device, edition 10/2005. Refer to section 3.3 for conductor preparation, section 3.4 for terminal wiring and Table 8-1 for electronic-block assignments. The document number is EWA-4NEB 780600902-05.
Related topics
ET 200 system structure · ET 200 connection modules · ET 200 additional modules and accessories · ET 200 power supply modules · ET 200 power distribution modules. These links introduce different components within the range; compatibility is assessed against the complete order number.
Navigation: Siemens automation · Siemens S7 PLC · SIMATIC S7 · Siemens ET 200.
Technical sources: Siemens Industry Mall, 6ES7193-1CH10-0XA0 product record; Siemens ET 200L Distributed I/O Device, 10/2005, sections 2.1, 3.3, 3.4, 7.1 and Table 8-1.