6ES7 193-0CD40-0XA0
Siemens 6ES7 193-0CD40-0XA0 – ET 200B TB8 Analog Terminal Block
Siemens 6ES7 193-0CD40-0XA0 is the TB8 terminal block for ET 200B analog electronics blocks, within the SIMATIC ET 200 family. It uses spring-loaded terminals with a four-wire connection arrangement. This product belongs to the ET 200 terminal block range.
When sourcing a replacement, identify both the terminal base and the electronics block fitted to it. The electronics determine the measurement function and signal processing; the TB8 designation alone does not identify the signals supported by the assembled station. Our guides to PLC operation and the Siemens ET 200 system explain how distributed I/O fits into the wider control architecture.
Technical Data and Power Supply
The manufacturer specifies 24 V DC nominal supply, with an allowable range of 18.5–30 V DC including ripple. Protection is IP20 and the operating temperature range is 0–60 °C. Listed dimensions are 160 × 130 × 59 mm, in width × height × depth order, with an approximate listed weight of 600 g.
Check the voltage reaching the station while it is operating, as well as the output of the power supply. Cable resistance and poor connections can cause a voltage drop between those points. When assessing a DIN rail power supply, include the field devices sharing the supply in the load calculation and review the associated fuse protection against the cabinet drawings.
Compatible Analog Electronics Blocks
Siemens lists TB8 with 6ES7 134-0KH01-0XB0 / ET 200B-4/8AI for millivolt, resistance thermometer and thermocouple applications; 6ES7 134-0HF01-0XB0 / ET 200B-4AI for voltage/current inputs; and 6ES7 135-0HF01-0XB0 / ET 200B-4AO for voltage/current outputs. Available ranges and channel counts depend on the electronics and operating mode.
“TB8” does not mean that every assembled station provides eight analog inputs. Read the complete order number of the installed analog input module before selecting a replacement. A directly connected temperature sensor and a temperature transmitter with an analog output require different checks, even when both represent the same process temperature.
Understanding the Field Signal
4–20 mA signals and 0–10 V signals have different electrical requirements. If a replacement pressure sensor uses a different output type, moving a wire is not a complete conversion. Check the electronics capability, channel configuration and software scaling together.
The four-wire description refers to the terminal arrangement; it does not require every connected sensor to have four wires. Establish how the field device is powered and what signal it produces before choosing a wiring diagram. A loop-powered transmitter, a separately powered transmitter and a resistance thermometer should not be wired as though they were interchangeable.
Station Address, STOP/RUN and Analog Coding
The TB8 incorporates station address switches, a STOP/RUN switch, a fuse, analog coding elements and the PROFIBUS-DP connection. Coding must match the electronics and measurement wiring. A changed station address becomes effective after switching from STOP to RUN.
Compare the physical settings with the station configuration in the control project. For background, see PROFIBUS and PROFINET explained and our ET 200 communication interface category. Products sharing the ET 200 family name should not automatically be treated as having the same connections or configuration requirements.
Spring Terminals and Cabinet Wiring
Reliable wiring starts with the correct conductor preparation and terminal operation. The guide to spring connectors and screw terminals explains the general differences. Do not apply a screw-terminal tightening procedure to a spring connection; use the conductor preparation requirements in the relevant equipment manual.
Arrange sensor cables and connectors so that cable weight does not pull on the terminals. Leave identification readable and provide access for maintenance. Select STOP before fitting or removing the electronics block. STOP does not establish that all field wiring is electrically isolated; disconnect the relevant supplies safely before working on the connections.
Shield Connections and the -7XA0 Accessory
6ES7 193-0CD40-0XA0 is the terminal block; 6ES7 193-0CD40-7XA0 is its shield connection accessory. These are different items. When the shield connection element is used with rail mounting, the station must be installed horizontally.
Treat cable shielding, signal reference and protective grounding according to the application drawings. A universal rule about connecting every shield at one end or both ends is not a substitute for checking the circuit. Pay particular attention to analog cables near AC drive power wiring and circuits switched by contactors. Cable routing and shield continuity are useful inspection points when readings become unstable.
Investigating Incorrect Analog Readings
An unstable or incorrect measurement does not, by itself, identify a defective terminal block. Compare the physical field signal, the raw channel value and the final engineering value in that order. If the measured current is steady but the HMI panel displays the wrong pressure, investigate the configured range and scaling as well as the hardware.
A SCADA trend can also help establish when the problem occurs. Spikes that coincide with a motor starting provide a reason to examine interference, supply behaviour and reference connections. That timing is a diagnostic clue, rather than proof of a particular component failure.
Editor's Advice
Before replacing the base, photograph the electronics order number, station address, coding positions and cable labels. Those records make it easier to compare the replacement with the working configuration. When inspecting a used unit, check terminal grip, contact condition, housing damage and the mechanical operation of the switches. Confirm the actual supply scope, including whether the electronics block and any accessories are included.
Technical Documentation and PDF Manuals
Visit our Siemens ET 200 PDF manuals page for documentation covering wiring, analog coding and electronics blocks. Select the ET 200B documentation and the section matching the complete electronics order number. This product description does not replace the wiring diagram for the actual application.
Related Topics
For other station components, browse ET 200 connection modules and ET 200 additional modules. Compatibility with TB8 must be checked separately for each item.