6ES7 193-0CA30-0XA0

6ES7 193-0CA30-0XA0 is the TB3/DC terminal block for Siemens SIMATIC ET 200B distributed I/O systems. Designed for digital electronic blocks, it provides three-wire spring terminals in a 160 mm wide format. When sourcing a connection base for an existing Siemens ET 200 station, check this reference together with the order number on the fitted electronic block.

Device Description

The TB3/DC holds the field wiring and receives the electronic block. Its 16-channel terminal layout serves input, output or mixed functions determined by the installed electronics. Select the terminal block together with the module that defines the station's function.

The base includes the PROFIBUS-DP connection, station address setting and RUN/STOP switch. Recording both component references and the existing address helps when comparing the physical installation with the PLC project. Our PROFIBUS and PROFINET information page explains the communication terminology.

Technical Data

Manufacturer: Siemens
Model reference: 6ES7 193-0CA30-0XA0
Order number without spaces: 6ES7193-0CA30-0XA0
System family: SIMATIC ET 200B
Designation: TB3/DC terminal block
Electronic block type: Digital
Terminal layout: 16-channel base
Connection arrangement: Three-wire spring terminals
Width: 160 mm
Rated supply voltage: 24 V DC
Permissible supply range: 18.5–30 V DC, including ripple
Protection rating: IP20
Operating ambient temperature: 0 to +60 °C
Conductor cross-section without ferrules: 0.08–2.5 mm²
Conductor cross-section with ferrules: Maximum 1.5 mm²

Supply and environmental values come from the manufacturer's product data sheet; conductor sizes come from the ET 200B system manual. Cabinet design must also account for the installed electronic block's load, temperature and mounting requirements. Include sensors, output loads and other consumers when sizing the power supply. Our DIN rail power supply section provides related product options.

Examples of Compatible Electronic Blocks

Siemens documents the TB3/DC with electronic blocks including ET 200B-16DI — 6ES7 131-0BH00-0XB0, ET 200B-16DO — 6ES7 132-0BH01-0XB0 and ET 200B-8DI/8DO — 6ES7 133-0BH01-0XB0. These provide input, output and mixed I/O examples respectively.

A “16-channel” description alone is insufficient when ordering a replacement. Check the existing electronic block's complete reference and wiring diagram. Related products can be reviewed in our ET 200 digital input modules and ET 200 digital output modules sections.

Wiring and Installation Recommendations

Conductor preparation matters when working with spring terminals. Avoid damaged strands, crushed ferrules or wire ends that must be forced into the terminal opening. Before disconnecting a sensor, record its cable label, terminal number and field location together. When replacing sensor connectors and cables, verify conductor colours against the cabinet drawing.

Installation and removal should be carried out by qualified personnel after safely isolating the relevant supplies. Check that wiring does not pull sideways on the terminals, that the housing fits without strain, and that the electronic block contacts are clean. Cable ducts and other control panel components should leave the connections accessible.

Fault Checks and Commissioning

If one signal is affected, begin with its field device, cable and terminal contact. Record whether the symptom changes when the cable moves; that observation can help locate an intermittent fault. If several signals fail together, include shared supplies and connection points in the inspection.

Before testing outputs, establish safe conditions for any connected mechanism that could move. Where external relays and sockets are fitted, inspect their coil voltage, wiring and contact condition. Check the command, supply and load circuit separately before attributing a failed output to the terminal block.

If the station does not communicate, compare its address setting with the project record and inspect the communication connections. Record each change and its result instead of changing several settings at once. Related hardware can be found under ET 200 communication products and ET 200 connection modules.

Editor's Recommendations and Related Topics

For an older installation, a clear label photograph and an accurate wiring record are useful starting points. Provide both the terminal base reference and the electronic block reference when sourcing a replacement. Also confirm whether the supplied item includes the electronic block, connectors or other accessories.

For comparison within the product family, see 6ES7 193-0CA10-0XA0 and 6ES7 193-0CA40-0XA0. These links do not establish direct interchangeability; verify the required combination in Siemens documentation. Our Siemens ET 200 overview provides further background.

User Manuals and PDF Documents

+ Siemens ET 200 user manuals — PDF archive page.
+ Siemens 6ES7 193-0CA30-0XA0 — ET 200B system manual — TB3/DC drawing and terminal numbering: section 7.2.3, printed page 7-7, PDF page 93.
+ Siemens ET 200 general catalogue archive — Use the ET 200B system manual above for this model's wiring information.

++ Siemens Automation Main Page
++ Siemens Automation Contact — For enquiries to Otomasyon AVM.

Reminder: Confirm current availability, product condition and scope of supply for Siemens 6ES7 193-0CA30-0XA0 before purchasing. Some devices offered by Otomasyon AVM are used products; assess the individual description and photographs accordingly. Products will not be restocked once available stock is exhausted.

Note: The information, commissioning suggestions and documents on this page are provided for general guidance, are non-binding and may be updated. For definitive application details, consult the device label, the installed electronic block's documentation and the manufacturer's manual. The Otomasyon AVM Community welcomes practical feedback. You can share your operating experience and suggestions with us.